20 Most Recent Mitsubishi CS-35707 35" TV - Page 7 Questions & Answers

anytime something is taken apart, the reverse procedure invariably leaves something out. recheck everything b4 creating a projectile.

Hi Patrick, I pass the link to the service manual of your Mitsubishi TV I hope you can resolve your concern Greetings Franco Dosil Hola Patrick, te paso el link del manual de servicio de tu TV Mitsubishi Espero puedas resolver tu inquietud Saludos Franco Dosil https://elektrotanya.com/mitsubishi_wd-60638_65638_73638_60738_65738_73738_82738_65838_73838_82838_60c10_65c10_73c10_chassis_v43_v43c_v43-plus_sm.pdf/download.html

I have a Mitsubishi WD73642 model which I'm having a problem with it turning off. When power is turned on the status light flashes green and appears to be powering up. Then u hear sound. Picture comes on light turns sold green then within a minute the El TV will just turn off no other dianososis lights. TV is not located too close to the Wall. Any ideas why?

The bulb is out. You can purchase on amazon for around $20.00. It is a very simple fix. Should take about 5-10 minutes

Sounds like its overheating.
Are the fans working properly?

Did you buy a quality bulb (or one of the cheap junk bulbs around $20-$30?)

The volume button on the remote or the TV is stuck. Try this first, Turn the TV on from the TV (put the remote in a different room) now turn it down from the TV if the volume stays down, the remote up volume is stuck. If it stays loud The main TV board needs to be replaced. If it stays down carefully take the remote apart. check for tiny screws in the batteries compartment if no screws it all clips. Now clean the remote (try not to touch the curcit board).

Do you have the model number available? It should be on the back or bottom of the unit. Before adjusting, clean the heads and verify that the tape is running at the proper height past each head. There are three head assemblies to inspect: the rotating video head, the stationary sync head, and the stationary audio head. The sync signal is on the top edge of the tape and the audio signal is on the bottom edge. If the sync head or an adjacent guide pin has come loose, that could cause tracking problems. Caution: the video heads are very delicate. They're located in the slots at the bottom edge of the rotating drum. Use a foam-tipped swab with straight isopropyl alcohol, and gently wipe the heads in the same direction as the tape goes (do not wipe perpendicular to the tape direction; you could snap the head off if it snags on the swab).

No error code 61 listed, only a 66 error code which indicates lamp issues: 66 A) Lamp did not turn on at P-ON sequence... Check CJ4 circuitry B) No Lamp Inserted............... No Lamp inserted C) Disconnected cable between ballast and lamp.... HV connection or lead wire to lamp. D) Lamp-Enable goes to PWB-MAIN but not to Ballast....Lamp Cartridge Failure for lamp see the following web site: http://www.shopjimmy.com/dlplamps?tv_brands_select=Mitsubishi&tv_models=Mitsubishi+WD-73638 recommend using the manufacture part# as many replacements for Mitsubishi will not work.

Shorted circuit board.

It might help to unplug the TV from the AC outlet for a few minutes, and hope that it's circuit resets itself.

Could be you need to set the output volume on your receiver for the soundbar. Most receivers allow volume output for each speaker

https://www.youtube.com/watch?v=_ONPuB5L-x4 https://www.youtube.com/watch?v=C9uA1DcyeNI https://www.youtube.com/watch?v=INird71KKtA

Go to this link, find the manual and follow the instructions. https://www.manualslib.com/

https://www.manualslib.com/products/Mitsubishi-Ws-55411-281606.html

BLINKING

https : // www . manuaiscenter . com / manuals / mitsubishi / hsm1000g - servi?o - manual . html #. XH5euon7QdU Detalhes

Do you see a small fan close to it? Is it gunked up with dust? It could be the bulb but it sounds like it isn’t getting cooled.

Yes, but if you leave it unplugged for at least 1/2 hour you should be safe. Use insulated tools or rubber gloves to be sure.