20 Most Recent Janome Even Feed Foot w/Quilting Guide - Page 6 Questions & Answers

Well, no matter where you are in the world, Wikipedia has a list of model train clubs in your country it seemshttp://en.wikipedia.org/wiki/List_of_model_railroad_clubs

First try and get as much glue that is left in between the left over pencil and the tip out. Then find something that is the same diameter as the tip of the glue gun and about 6 inches longer that the length of the gun. With the glue gun OFF jam the object into the tip of the glue gun until it comes out the rear of the gun. Whatever you find to do this needs to be stiff like wire or something of the sort.

I found a cheap way to clean silver candle stands on this website. Hope it helps. https://www.ehow.com/how_5910236_clean-silver-candle-sticks.html

You didn't ask a question. Do you have one? Want one? How to wire it to operate? This is a good resource on the accessory: https://www.tandem-associates.com/lionel/lionel_trains_345_acc.htm

Use either clear epoxy glue on the back side or clear gorilla glue. Hold front side together/ in place until it fully drys

notify manufacturer for instructions or online search using make and model

The bevel is at the fR end for cutting. It leans downwards with blade at bottom. Other end, often rounded and thicker stays up top.

on what

The maximum operating speed is 320 km/h (200 mph) (on a 387.5 km section of the T?hoku Shinkansen). Test runs have reached 443 km/h (275 mph) for conventional rail in 1996, and up to a world record 581 km/h (361 mph) for maglev trains in 2003.

Watch this video. https://www.youtube.com/watch?v=uj_6U46pnn8

Does it use batteries or is it picking up current from the rails and a supply transformer?

Most remotes have a small "slide out" section on the rear, which one uses a fingernail to eject. Then inside will be the battery. Not which side is + and - and the battery type. If battery has corroded or left whits residue - a knowledgeable person needs to review & assist.

Hi, check out these tutorials to learn how to use it : https://learn.cricut.com/maker/getting-startedhttps://tgw.onl/digitalocean/ https://tgw.onl/siteground/ https://tgw.onl/ipage/

Hi,Allow the glue gun to heat up.Load a glue stick into the gun and pull the trigger. Use the new glue stick to help push out as much of the old stick as you can. If you can, push out the entire old portion and pull the new stick back out with your fingers.Use a metal stick, such as a paperclip pulled out straight, to scrape out the nozzle of the glue gun. Do this if the glue is old and doesn't flow well.https://appsync.biz/dafont/ https://192168ll.onl/ https://appsync.biz/filehippo/

How could you, except by contacting AMT? Failing that, how does your search engine of choice fail to find a substitute?

https://www.ebay.com/itm/PIKO-Model-H0-HO-1-87-Scale-Train-Track-lost-parts-Lot/223441376758?hash=item340624d5f6:g:xbEAAOSwRG1cg5wr&frcectupt=true

There should be two screws on the back of the control / power supply...just connect a wire from each screw to each screw (two of them) on one of the track pieces. it the train is running the wrong way...switch the wires on just one screw set..

http://powertool.manualsonline.com/manuals/mfg/metabo/metabo_saw_product_list.html

Sound and motion decoder are the same address. Try F8 that mutes and unmutes the sound, If that doesn't work Change CV 8 to 8, that resets the decoder to factory settings. You will have to re enter the address as the decoder reverts to address 03. If all else fails check that the speaker is wired properly, if that doesn't work you may have a bad decoder that should be under warranty. Good luck

Is that even a real word?

Hows this? "I was asked, how would I use the word adhesively in a sentence."