Top 20
Nostalgia Electrics Classic Music Jukebox Retro Nostalgia AM/FM Radio CD Player Shelf System Questions & Answers
NSM Proformer cd jukebox flashes er73 and will not
error 73 means error during grip from magazine check for lift jamming,check function and adjust,i had one recently the same fault found it easy to replace the cd changer complete for 65.i do have the manual and service guide if you need one just email me
1/18/2010 3:35:30 AM •
Nostalgia...
•
1,418 views • 0 helpful votes
Hi i hav a 470 rockola jukebox it dosnt seem to
The problem is probably in the keyboard. Clean all the contact switches you can get to with very fine sandpaper. The reason it is stuck is it is waiting for that third selection to complete the circuit.
1/20/2010 12:50:25 PM •
Nostalgia...
•
992 views • 1 helpful votes
The third select button will not stop down
I have a model 464 and my problem was similar but mine was the second digit.I replaced the p c board in the selection control box and my problem was gone.I would check the selection control box.Hope this helps
12/14/2009 9:26:32 PM •
Nostalgia...
•
572 views • 1 helpful votes
I have a Seeburg MCU3 Prelude - had is repaired a
No, but like any machine, it does need lubrication once in a while. You should purchase a manual for it (eBay).
If the clutch has become stuck, it's time to call in a pro.
Are you sure it's in "PLAY" mode? Check to be sure the service switch is in "PLAY."
Does the motor turn?
If yes, try pressing the reject button on the back. Maybe it's stuck thinking it's playing a record in an empty slot (clamp arm will be against the turntable). There is also a manual trip lever just to the right of the tonearm. lift up on it if the motor is turning and see if that triggers it. Go ahead, it won't hurt you.
if the motor itself has frozen up from lack of oil, try putting some light machine oil (NOT 3-in-1 or anything paraffin based) in the oil cups on the side of the motor and letting it sit for a few hours. Then, turn the motor shaft by hand a little. This may free it up. if so, count your blessings and call someone in to give the whole mechanism a proper lubrication or something else will eventually seize up or wear out.
Good luck.
12/24/2009 2:01:36 AM •
Nostalgia...
•
303 views • 0 helpful votes
Cracked rowe cover
THIS IS A COMMON PROBLEM. THE ONLY SOLUTION IS TO REPLACE THAT DOME.
GLUING WILL NOT WORK. APOXY WILL NOT WORK. THERE IS A LOT OF PRESSURE
AT THAT PLACE.
REPLACE THAT DOME IS THE WAY TO GO. GET N FRIENDS TO HELP, OR YOU WILL BREAK THE NEW DOME.
[email protected]MAME IS SEYMOUR LEVITT
COMPANY NAME IN-HOME JUKEBOX REPAIR
6362273300
746 HENRY AVE BALLWIN MO.
6/7/2009 9:20:03 PM •
Nostalgia...
•
223 views • 0 helpful votes
How do i change needle on record player no
release the orange case from the back and slide forewards.Note,use athin knife blade to ease the case sides 2no. from holding points on head.BUT THERE MUST BE A BETTER WAY???.
11/25/2009 6:19:21 PM •
Nostalgia...
•
79 views • 0 helpful votes
Openfit Shokz battery replacement?
Question edited for clarity, typo and CAPS.
Question moved from Cars and Trucks category.
Claim on the warranty irrespective of how long you have had them. They charge $180 but they cost them $20 to buy from China. Package them up and send them tracked and ask them to replace the batteries.
How long is the warranty on AfterShokz?
While we hope you never need it, all new Shokz purchased from authorized retailers come with a two-year warranty that begins on your date of purchase.
Jan 11, 2019
https://www.google.com/search?q=Openfit+Shokz+battery+replacement
..
How do I change to degree mode on my porpo YH-2000
- Power Off: Turn off the device.
- Jumper Configuration: Locate the jumper labeled "S16" on the device. Initially, it should be connected to pins 2 and 3.
- Power On (Alarm+All LEDs Flashing): Turn the device back on. You'll see the alarm LED and all other LEDs flashing.
- Power Off Again: Turn off the device once more.
- Jumper Adjustment: Change the jumper configuration from pins 2 and 3 to pins 1 and 2.
- Finished: Your Porpo YH-2000 is now set to the desired angular unit mode.
If you encounter any issues, you can press the reset switch on the back of the device to reinitialize it.
My roadking rk4000 wont charge. I turn it off to charge it but there is no indicator light at all, any suggestions?
Are you using the charging cables that came with it? That is a type C. Are you securely attaching the charging cable? A loose connection would keep the battery from charging. If you had a low battery, you would see a red light. That you have no light at all suggests there is no charge left in the battery. I'm not sure the reset will work with no charge which is why you ought to check the cables first.
But turn it off and then hold down the Multifunction button for 10 seconds to reset it. Then turn it back on and see what happens. If you can, test the charging cable on aother device. If you have another type C charging cable, try it, just to eliminate a bad cable. If these suggestions don't work, you may try the manufacturer's customer support.
Can f2100 remote work on my dishtv box?
The F2100 remote is not explicitly listed as compatible with the AerialBox T2100, I recommend using the remote that came with your AerialBox T2100 for optimal functionality. If you have any specific compatibility concerns, I suggest reaching out to Dish TV customer support for further assistance.
Audiosonic CR-06PL not changing time when following manual instructions.
Set Time Hours and Minutes: Press Time/12/24 and Alarm1/ON/OFF buttons at the same time for two seconds and it will start to blink the hour.
Press and hold the button for a fast setting or tap it briefly to increase the setting by one hour. Now set the minutes with time (press and hold) and min.
How do I set the Audiosonic clock? Set current time Press and hold the time button and simultaneously press the hour to set the hours in 24-hour mode .
Not finding what you are looking for?