Top 20
Pyramid 801 10-Band Car Equalizer - Page 6 Questions & Answers
Color code for factory wiring harness for 05 Hyundai Elantra
I found a wiring diagram for the 2005 Hyundai Elantra that might be helpful . According to the diagram, the color codes for the factory wiring harness are as follows:
Wire Color Function
Orange/Black 12V Constant
Yellow 12V Accessory
Black Ground
Blue/Black Power Antenna
Green/Orange Illumination
Brown/White Left Front Speaker (+)
Black/White Left Front Speaker (-)
Brown/Yellow Right Front Speaker (+)
Black/Yellow Right Front Speaker (-)
Brown/Red Left Rear Speaker (+)
Black/Red Left Rear Speaker (-)
Brown/White Right Rear Speaker (+)
Black/White Right Rear Speaker (-)
If you don't have a plug on your factory wiring harness, you can hardwire it by connecting each wire to its corresponding wire on your new stereo. You can use crimp caps or soldering to make the connections
. If you're not comfortable with hardwiring, you may want to consider purchasing an aftermarket wiring harness that clips onto the factory harness you removed off the rear of your factory radio during its removal. This will make it easier to connect your new stereo to your car's electrical system .
Hyundai Radio Wiring Color Codes - Radio Codes Calculator
I just installed a brand new VR-1032XB and on first start up I got a white screen.
If you have just installed a brand new VR-1032XB and are experiencing a white screen on first start-up, there are a few potential causes and troubleshooting steps you can try:
- Check the connections: Ensure that all cables and connections between the VR-1032XB and your display device (e.g., monitor, TV) are secure and properly connected. Make sure you have connected the appropriate video output from the VR-1032XB to the corresponding input on your display device.
- Check the display settings: It is possible that the VR-1032XB is outputting a resolution or refresh rate that is not compatible with your display device. Try accessing the display settings on the VR-1032XB and adjusting the resolution or refresh rate to see if it resolves the white screen issue. Refer to the user manual or manufacturer's documentation for instructions on accessing and changing display settings.
- Restart the VR-1032XB: Try powering off the VR-1032XB and then turning it back on again. Sometimes, a simple restart can resolve temporary display issues.
- Test with a different display device: Connect the VR-1032XB to a different display device (if available) to see if the white screen issue persists. This will help determine if the problem lies with the VR-1032XB or the original display device.
- Contact customer support: If none of the above steps resolve the white screen issue, it is recommended to contact the customer support of the VR-1032XB manufacturer. They can provide further assistance, troubleshooting guidance, or advise on any potential hardware defects or software issues.
I can't pit CD plate in player
Assuming your player is
Pioneer VSX-902 receiver's CD player, here are a few troubleshooting steps you can try:
- Verify the correct placement: Make sure you're aligning the CD properly with the CD tray. The label side of the CD should be facing up, and the CD should sit flat on the tray. Some CD players may have specific guides or markings to indicate the correct placement.
- Check for any obstructions: Inspect the CD tray and the surrounding area for any debris, dust, or foreign objects that might be obstructing the tray from fully opening or closing. Gently clean the tray and the CD player's surface using a soft, lint-free cloth.
- Press the eject button: Before attempting to insert a CD, press the eject button on the CD player to fully open the tray. If the tray doesn't open, there may be a mechanical issue with the CD player that requires professional attention.
- Power cycle the receiver: If the CD tray is stuck or unresponsive, try power cycling the receiver. Turn off the receiver, unplug it from the power source, wait for a few minutes, and then plug it back in and turn it on. This may reset the CD player and resolve any temporary issues.
- Contact Pioneer customer support: If you've tried the above steps and still can't insert a CD into the player, it's best to contact Pioneer customer support or consult a professional technician. They will be able to provide specific guidance for your model and help troubleshoot or repair any underlying issues with the CD player mechanism.
It's important to exercise caution when attempting any repairs or troubleshooting steps with electronic devices. If you're unsure or uncomfortable with performing these steps yourself, it's recommended to seek professional assistance to avoid any potential damage to the equipment.
Not finding what you are looking for?
