20 Most Recent Toshiba 1360 Black and White Copier - Page 8 Questions & Answers

This means that the operating system on the hdd fails to start. The hdd is probably failing and needs replaced.

https://printcopy.info/?l=en&mod=erc&brand=Toshiba&model=e-Studio%20283&code=C970 C970

Description

Process related service call High-voltage transformer abnormality: Leakage of the main charger is detected.

Causes

Remedy

1. Is the main charger installed securely? 2. Check if the spring of high-voltage supply contact point is deformed. 3. Check if the needle electrode is broken or the main charger grid is deformed. 4. Check if any foreign matters is on the needle electrode or the main charger grid. 5. Check if the transfer roller and the separation needle are installed securely. 6. Check if the transfer roller or the separation needle is removed. 7. Check if there is any foreign matter attached on the transfer roller or the separation needle. Toshiba Studio 283 Error Codes

08-2002 set to "0" If problem persist, u need to check fuser unit especially themistor

Image quality control test pattern abnormality: The test pattern is not formed normally.

Image quality control test pattern abnormality

CE40 is image related error, u need to check which pu giving the problem...

C447 Error - Heater lamp abnormality after abnormality judgment (temperature abnormality at ready status) Power voltage Check if the power voltage is normal.(Is the voltage during the operation ±10% of the rated voltage?) Thermopiles • Check if the fuser belt center and side thermopiles (front, rear) are installed properly. • Check if the harnesses of the fuser belt center and side thermopiles (front, rear) are open circuited. Power supply unit and fuser unit • Is the fuser unit installed correctly? • Check if the heater lamp is broken. • Check if the connector of the heater lamp is disconnected. • Check if the thermostat is blown • Check if the connectors of the power supply unit are disconnected (power supply unit AC output connector CN408, CN409 and LGC I/F connector CN404 CN405). • Check if the power supply unit is abnormal. LGC board • Check if the connectors CN333, CN345 and CN361 are disconnected. • Check if the conductor pattern on the LGC board is short circuited or open circuited. Status counter After repairing the matter which caused the error [C411/C412], perform the following: • Turn ON the power while [0] and [8] are pressed simultaneously • Key in "2002", then press [START]. • Change the current status counter value "1 " or "2 " to "0", then press [OK] or [INTERRUPT] (to cancel [C411/C412]). • Turn the power OFF and then back ON. Make sure that the equipment enters the normal ready state. 5 Clear the status counter Change the current status counter value (08-2002) "3", "5", "6", "9", "19", "21", "22", "23", "24", "25", "27", "29" or "32" to "0" for [C44X], taking the same procedure as that for [C41X]. * The status counter value is as follows in the following cases. - The error occurred during warming-up: "3", "5" or "6" The error occurred after the equipment has become ready: "7". - The temperature detected by the fuser belt center thermopile is 220°C or higher, the temperature detected by the side thermopile is 230°C or higher or the temperature detected by the front thermopile is 250°C or higher: "9", "19", "21", "22", "23", "25", "27" or "29" - The error occurred during printing: "24" or "25". - The error occurred during energy saving: "27". - A paper jam occurred: "29".

fuser related problem but try out this Check if the connectors are disconnected. (2) Check if the center, side and edge thermistors are in contact with the surface of the fuser roller properly? (3) Check if the harnesses of the center, side and edge thermistors are open circuited. 2. Check the heater (1) Check if the heater is broken. (2) Check if the connector of the heater is disconnected. (3) Check if the thermostat is blown. 3. Check the LGC board (1) Check if the connectors CN308 are disconnected. (2) Check if the conductor pattern on the LGC board is short circuited or open circuited. (3) Replace the LGC board. 4. Clear the status counter After repairing the matter which caused the error [C410], perform the following: (1) Turn ON the power while [0] and [8] are pressed simultaneously. (2) Key in "400", then press [START]. (3) Change the current status counter value "1" or "2" to "0", then press [ENTER] or [INTERRUPT] (to cancel [C410]). (4) Turn the power OFF and then back ON. Make sure that the equipment enters the normal ready

the code should be 08-2002

This is a Hard drive failure. The hard drive would need to be replaced and firmware installed on it to resolve your problem.

F101 is HDD related error

"Call for service" means call to have a repair technician come out to fix the machine.

You need to check that your Printer is not in Printer Offline using mode. For this, you need to go to Devices in Windows settings and then click on Printers. Now, choose your own Printer from the list and then click on Open queue. Make sure that the Use Printer Offline option is unchecked. If it is checked, uncheck it.

Anonymous OP Poster from Jan 2014. POP3 has nothing to do with printers. It is email only. What is a POP serverPost Office Protocol version 3 (POP3) is an mail protocol used to retrieve mail from a remote server to a local email client. POP3 copies the mail from the remote server into the local mail client. Optionally, mail is deleted after it is downloaded from the server. This saves space on the server.

IMAP vs POP3 vs SMTP: Which is best to use? - Navigator ...

Anonymous in 'Additional Information' 11 November 2012. You should be answering down here. Also try to include links to Toshiba Customer Service like this.

Support ' Toshiba Canada

https://www.toshiba-lifestyle.com > Support TOSHIBA LIFESTYLE PRODUCTS & SERVICES CORPORATION · Canada. 1-855-238-5607. Canada Sales and Management Office. 215 Shields Court, Unit 2 Markham, ON L3R 8V2. ..

Get support for your 4530c here: http://business.toshiba.com/usa/support/downloads.jsp?site=usa Good luck.

'Anonymous'. Check your dates. You are replying to lots of posts from 2013 and 2014. These are posts that have had Spam removed from them today which has brought them to the top of the list again. Also, you are answering in the area that asks for 'More Information'. Your answers should be down below. Also answering in 'Anonymous Mode', means you get no points or awards.

U need: Print kit ( u can print or scan via e-filing/file downloader, cant use the SCAN button) Print/scan kit ( Scan button let u scan to fileshare, scan to email etc...)

Connect to copier/scanner using web browser. Click Administration tab, and logon use the copier's username/password. Click Network Click SMB Session Click SMB Session box In section called "SMB Signing of SMB Server", the default of "If client agrees, digital signature is done for communication" needs to be changed to "Digital signature isn't done for communication for the server" Click Set button at top, then Save button, and the copier will reset.

http://business.toshiba.com/downloads/KB/f1Ulds/8298/es4520c-Troubleshooting-v03.pdf https://www.manualslib.com/manual/171887/Toshiba-E-Studio-555.html?page=93 https://www.youtube.com/watch?v=FbGSN3GXeIc

check the charge cleaner for that color it might be stuck in the middle of the pin array