20 Most Recent Kalamazoo Outdoor Gourmet Kalamazoo 610 Metal Band Saw Service Parts Manual - Page 3 Questions & Answers

There could be several potential causes for the issue you're describing with your brushless 18Vlt paddle switch grinder.

1. Overheating: If the grinder is running for an extended period of time, it can overheat and shut off as a safety measure. If this is the case, the grinder will need to cool down before it can be used again.
2. Battery Issue: The grinder may be shutting off because the battery is not providing enough power. This can be caused by a damaged or worn out battery, or by a problem with the battery's connection to the grinder. Make sure the battery is fully charged, check and clean terminals, test battery with other tools, if there is no improvement consider getting new battery
3. Power switch issue: The switch could have a problem and it's malfunctioning, preventing the grinder from operating properly. The switch may need to be replaced in order to fix the issue.
4. Motor issue: A problem with the brushless motor itself, could cause it to shut off under load or malfunction. The motor may need to be inspected and repaired or replaced.
5. Power supply: If the grinder is running off of AC power, rather than a battery, the power supply may be faulty or not providing enough power to the tool.

I suggest you to start with trying to identify the problem by eliminating each possibility one by one. If you are not comfortable troubleshooting and fixing the tool, it may be best to reach out to the manufacturer or take it to a professional repair shop.

That is commonly called a throat plate and we need to know what the make and model of the saw is.

if it has one it will be on motor

Your start windings are toast. If it has a capacitor start (a big lump stuck to the side of the motor) it might be bad.

It is not ideal having a power strip due to the amps it draws, but the fact it hums, leads my to believe that the start/run capacitor on the motor might be failing.

probably not the glue would have to conduct electricity.

All questions need 'make model (what it is)' as the first three words in every question please Bob. You can Google make model recommended saw blades https://www.google.com/search?q=What+type+of+saw+blades+can+be+used ..

test switch for failure

I would suggest calling Hilti direct at 1-800-879-8000 and speak with their tech department and they will be able to assist you in locating parts and your mfr question

Hi, please check your local home depot or lowers for the part. You can call them or search their website for the product. Thank you.

Hi, In this case, it might be best to reach out to the manufacturer in order to get find the safe and most affordable replacement for your bandsaw. If you don't want to use that route, please reach out to your local Home Depot store via phone to have them check their catalog of products for your gear. Thank you.

There is a button on the saw that holds the shaft still. Unplug the saw and put light pressure on this button while you slowly turn thr blade by hand. When it gets to the hole, the button will drop into the shaft. Keep it pressed down and unbolt the nut.

Greetings from Toronto - ish. I am in Canada so my searches are normally weighted to Canadian suppliers. In this case none are .ca However Repair Clinic do supply to Canada and have a 1-800 number that states it on the Contact page. https://www.google.com/search?q=terratek+sliding+mitre+saw+parts ..

the belt shape new will not effect replacing it. It does not stretch but slides on. Did you loosen screw? Refer to instructions page 19-20. Tey calling the number listed in instructions. https://www.manualsdir.com/manuals/79545/elektra-beckum-kgs-303.html?page=19 ..

The links in here says there is. https://www.google.com/search?q=Model+3320445+compressor+reset ..

First, I'm not a "Benchmark" representative. * Check your warranty. Call for support. * Amazon supports "Benchmark Abrasives"; https://www.amazon.com/stores/node/7925658011?_encoding=UTF8&field-lbr_brands_browse-bin=Benchmark%20Abrasives&ref_=w_bl_hsx_s_hi_web_7925658011 *** Following is for information only.*** * Review; https://modernwoodworkersassociation.com/penultimatewoodshop/2013/04/benchmark-miter-saw-station-review.html * Forum review of 3" saw ; https://forum.canadianwoodworking.com/forum/tools/power-tools/30520-benchmark-3-circular-saw * Facebook (knife, blades); https://www.facebook.com/Benchmark-Knife-Saw-1514585088757599/ * Ebay; https://www.ebay.com/sch/i.html?_from=R40&_trksid=m570.l1313&_nkw=benchmark+saw&_sacat=0 Aloha, ukeboy57 Additional related info; * Master force; https://hw.menardc.com/main/items/media/SUMEC001/Install_Instruct/240-0021MasterForce10InchMiterSawOwnersManual2015.pdf * Ridgid; https://images.homedepot-static.com/catalog/pdfimages/97/97714f37-7bbc-4393-89c2-1874e976b0de.pdf * Porter Cable; http://pdf.lowes.com/useandcareguides/000999115006_use.pdf * Craftsman; https://c.shld.net/assets/own/00921236e.pdf

Link, Usually you will have to remove the blade guard to get access to that. There is usually a rubber stop with a screw going through it that you will have to remove, and a spiral spring clip on the inside of the hub of the blade guard that will also have to be removed and then you should be able to lift the blade guard off the saw. The spring will hook around the blade guard and the other end will hook to the saw housing. Hope this helps!

Is this it? https://awsparts.com/632874wt-water-tray https://www.google.com/search?q=kobalt+kb7005+replacement+parts ..