20 Most Recent Toro Lawnmower 20099 Mower Mowers Lawn - Page 5 Questions & Answers


First make sure your battery is fully charged. The charger on lawn tractors will not keep the battery fully charged as they just produce a light charge. Check battery before the starter but if battery is fully charged then it's possible the starter could be bad.

Toro Garden | Answered on Jul 25, 2019


Back firing could be an ignition, or valve timing issue, also check the function of the anti fire solenoid on the bottom of the carb float bowl ( you should hear this click as the ignition is switched on) you can also remove it and watch the centre pin retract when the ignition unit is switched on, next thing to check is that the flywheel key has not sheared, this will involve removing the flywheel, failing this remove the rocker box cover and make sure both valves are moving freely as the engine cranks, it could be a stuck valve.

Toro Garden | Answered on Jul 17, 2019


The model number you listed comes up as a Murray riding mower.

Enter you model number at the Toro web site. I believe the manual will have the wiring diagram.
https://www.toro.com/en/customer-support

https://www.partstree.com/parts/ also will like have same. Just need the right model number.

Toro Garden | Answered on Jul 17, 2019


it says in your owners manual. or go to toro.com

Toro Garden | Answered on Jul 17, 2019


Jump onto www.toro.com and download the free service manual for your machine. Note down all the details on the ID plate on the mower, you will need it to find the correct manual......
From there you can get the part number. Good Luck!

Toro Garden | Answered on Jul 17, 2019


Jump onto www.toro.com and download the free service manual for your machine. Note down all the details on the ID plate on the mower, you will need it to find the correct manual......

Toro Garden | Answered on Jul 17, 2019


Disconnect the negative battery cable.
Raise and safely support the vehicle.
Remove the drive belt shield at the right wheel well.
Remove the drive belt.
Remove the drive belt tensioner mounting bolt.
Remove the drive belt tensioner.
https://www.ronmowers.com/brand/toro

Toro Garden | Answered on Jun 15, 2019


Did you clean the float bowl, it collects dirt and stops fuel to the needle valve

Toro Garden | Answered on Jun 13, 2019


Came up totally empty on the Internet searching for a video or even a description of how to replace this cable - so had to go blind into it. The top end of the cable installation is pretty easy to figure out. The trick, if you wanna call it that, is that to get into the lower end of the cable installation (under the engine) you have to have the mower on its side and remove the blade and the black plastic housing just above it (more than I had bargained for when I ordered the replacement cable, which comes with no directions at all). Two 1/2" nuts and you have the blade off; two hex-head 3/8" screws and you can just snap off the plastic housing. (Hint: The square, black plastic block holding the metal sleeve on the cable? Don't loosen it all the way cuz it's a bear putting back on. It's just a press-fit to hold the sleeve, so loosen it just enough to push the sleeve out of the block and then using a screwdriver pry the slot open enough for the cable itself to slide out.) Sounds pretty simple, huh? Unless, of course, you're going into it blind :)

Toro Garden | Answered on Jun 07, 2019

Not finding what you are looking for?
Toro Lawnmower 20099 Mower Mowers Lawn Logo

84 questions posted

Ask a Question

Usually answered in minutes!

Top Toro Garden Experts

Joseph Mueller
Joseph Mueller

Level 2 Expert

346 Answers

roeb

Level 3 Expert

819 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Are you a Toro Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Toro Garden

  • Toro Garden

Most Popular Question

no compression when pull cord

  • Garden
Loading...