20 Most Recent HEALTHRIDER S300i Treadmill Motor Control Board 14470 - Page 2 Questions & Answers

1) you have 3 problems: mechanical+ electrical + electronic.2) adjust the tensions from deck bel + drive belt motor3)test the main motor without load and see what happen.4)test the main motor board and see what happen.see block diagram

1) tight the flexible cord from keypanel vs display board2)tight the display board vs lower board(main motor board)3)Test the main motor board(faulty to worn deck belt)4)INCLINATION motor burn.5)Adjust Pot from the inclination motor6) the gear slip adjust or repair.see the block diagram

1) IF THE MACHINE ONLY RUN IN DEMO MODE, TRY TO RUN IN NORMAL POSITION.2)PUSH AND HOLD ON THE STOP BUTTON BY 5 SECONDS.3) IF THE PROBLEM PERSIST, TRY TO TIGHT THE FLEXIBLE CORD FROM KEY PANEL VS DISPLAY BOARD.4)TIGHT THE DISPLAY BOARD VS LOWE BOARD(MAIN MOTOR BOARD)5) IF THE PROBLEM PERSIST THE MAIN MOTOR CONTROLLER BOARD IS PROBABLY FAULTY.6)bEFORE TEST THE MAIN MOTOR.SINCERELY.Seethe block diagram

1)See if flexible cable from display board is bending to lower board.2)main motor board is faulty by worn deck belt.3) burn motor faulty.4) adjust the Potentionmeter from the motor (incline).5)Defective gear in inclination motor.See the block diagram

1) SEE IF SOMETHING IS PENDING between the folding section2) Your Pin is little bend.3) the receiver where the pin is coming is not adjusted.sincerely.

you can buy in fixya.comwww.fitnessrepairparts.comwww.gymparts.comwww.treadmilldoctor.comsincerely

you can try to rent a set at AutoZone. when you return it they will give your money back. try standard and metric. depending on manufacturer of treadmill.

Hi, press the Stop and the Speed Up keys down while inserting the safety key this will get the into calibration mode. The next step is to press the Stop key one time. The Time window should read EP:2P. Some newer models may also say FP, Pass, or the like. This means that it passes the EPROM test. if it says 2F, FF or Fail then the upper console needs to be replaced
Press either incline key and the incline will calibrate automatically.
BE CAREFUL, THE TREADMILL WILL RUN AT FULL SPEED IN THIS NEXT MODE! DO NOT STAND ON THE WALKING BELT. Press the Speed Up key and hold it down until 85 is shown in the Distance window (some models may show the 85 number in another window
If the belt does not move in this mode then the controller board is defective and needs be replace.

Hi,

This due the belt is loose problem.Here is the maintenance manual for your more help.

http://www.fitness-equipment.com/Manuals/Healthrider-Manuals/299300.pdf

Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thank you for using fixya have a nice day:-)

First be sure there is power at the outlet. Check that the power switch is on, and the circuit breaker is not tripped (beside the power cord).
Remove the hood and inspect the wiring. (unplug the machine first). Ensure that all connectors are tight and none are burnt. At this point if all appears to be OK, look for lighted LEDs on the power PCB. If all is dark, replace the power PCB ( approx $100). If the LEDs are lit, you may require a console, or the safety key switch might be defective. To check it, the console must be removed and the console base removed. Inspect and test the micro switch.
The console is no longer available.

hi it seem like the motor is fine but the belt on the motor either needs to be tightened or replaced. best way to find out is to take off the front cover showing the motor and step on the treadmill. if the belt isnt moving but the motor is spinning then you need to replace the belt on the motor. or you can try to adjust the belt. i had the same problem, i just tightened the belt and everything works fine.

Make sure you have power in the wall outlet by plugging in a lamp, etc. into the same outlet the treadmill is plugged into to test. Plug it in the exact same receptacle. Sometimes in an outlet one receptacle will work and the other won't.
Make sure any breakers are fuses that may have tripped or blown have been reset or replaced.. Use the same type of fuse. Changing the value of the fuse can be dangerous or cause a fire.
Make sure the power switch is turned on and the safety key is inserted into the console if you have a safety key.
Look for any test lights on the power boards beneath the motor hood. Use caution when removing the motor hood because you may still have electricity in the motor area even if the treadmill is unplugged.
Test for a motor control failure. Typically if you have a failure, the treadmill will continue to turn on and operate normally until you try to input speed. If the treadmill operates on what we call a closed-loop system, it will give you some type of error message. If it operates on an open-loop system, the computer will run normally but the motor will not turn.
If you have a multimeter, you can test to make sure you have DC output from the controller spades. First make sure you have 120 VAC going in to the controller. On most controls, you can use a linear taper potentiometer or jump the W and H circuits of the control with an insulated wire or insulated pliers and apply AC voltage. The DC output spades should output DC voltage if the control is good.
The motor can be tested by using a simple DC cordless drill or lantern battery. MAKE SURE TO USE A DC POWER SOURCE...DO NOT USE AN AC POWER SOURCE OR YOU CAN RUIN THE MOTOR.

just change the keypad

Press the Stop and the Speed Up keys down while inserting the safety key this will get the into calibration mode. The next step is to press the Stop key one time. The Time window should read EP:2P. Some newer models may also say FP, Pass, or the like. This means that it passes the EPROM test. if it says 2F, FF or Fail then the upper console needs to be replaced
Press either incline key and the incline will calibrate automatically.
BE CAREFUL, THE TREADMILL WILL RUN AT FULL SPEED IN THIS NEXT MODE! DO NOT STAND ON THE WALKING BELT. Press the Speed Up key and hold it down until 85 is shown in the Distance window (some models may show the 85 number in another window
If the belt does not move in this mode then the controller board is defective and needs be replace.

If the blue wire from the motor on your HEALTHRIDER H95T treadmill has broken at the metal connector and it's not listed as a part, you can try the following steps:

1. Contact the manufacturer: Reach out to the manufacturer of the treadmill to inquire about replacement parts or repair services. They may be able to provide you with a replacement wire setup or direct you to a service center that can help.
2. Find a similar connector: If you are unable to find a replacement wire setup from the manufacturer, you can try to find a similar connector at a local electronics store. Take a picture of the broken connector and bring it with you to help you find a matching one.
3. Repair the wire: If you are unable to find a replacement connector, you can try to repair the wire yourself. Use wire strippers to remove the broken wire from the connector and strip the end of the wire that is still attached. Then, use a wire splice connector to join the two wires together. Be sure to use a crimping tool to ensure a secure connection.
4. Seek professional help: If you are not comfortable repairing the wire yourself or are unable to find a replacement part, consider seeking the help of a professional. A qualified technician may be able to repair the wire or suggest an alternative solution.

It is important to ensure that any repairs or replacements are done safely and correctly to avoid injury or damage to the treadmill.

I hope you will get an answer soon. You can buy Provigil to reduce extreme daytime sleepiness. It also helps to bring alertness to your body.

We do not sell anything. Google the manual, they are free.