20 Most Recent Life Fitness 95Ti Treadmill 95 Ti - Page 2 Questions & Answers

Please RUN the software calibration for easy diagnostic and fix it. Go under the HOOD and read the instruction and proceed. God bless you

then you should know this is caused by worn belt and deck

make sure you have not set to mph

belt and deck worn

when I start up my treadmilll across the screens reads Motor-comm error. what coulld be the problem.I keep it clean and dirt free.

my Life Fitness 95 Ti can not go faster then 10 km/h.Please advice

1)You must shure the motor has level, use some one.use the washer according with the new motor.2) Tight very well with wrench.3) Alignment very well the drive belt, not much tension4) Lube the deck belt with the instruction manual.5) Lube the rollers bearing very well.6) Try to run the software calibration for diagnose, and troubleshootingGod bless you

Adjust the REED switch , see the diagram attached and proceed according. clean it, test for open or faulty. and tight the connector very well. see the block diagram. Run THE software calibration for easy diagnose, and fix it.God bless you

you will call to the company for better instruction. They are obligated to supply instruction for fix the control board. Do not waste your time Call them right now.God bless you

No do not use, until YOU LUBE. This happen because you must do it every 5 hours aprox of use, The machine protect itself the electronic system and shut down.Maybe the deck belt is worn.2) LUBE the rollers bearing very i3) test the drive belt, and test too the bearint of main motor and fix it.God bless you

RUN the software calibration for diagnostic,, troubleshooting, and fix it.God bless you

1) Run the software callibration for diagnose and troubleshooting and fix it. Read your instruction manual, if you do not have go www.fitness.manualsonline.com or www. iconservice.comsee the block diagram for better understandingGod bless you

you must read you instruction manual, if you do not have download from www.lifefitness. com or www.fitness.manualsonline.com or www.iconservice.com read the section troubleshooting code.However you must do the following>1) Test the sensor see the diagram2) Lube the shaft and gear from elevation motor 3) Test the elevation motor 4( adjust the sensor and clean,and tigh the connector wires.see my personal TIPS for HELP. see the diagram attached.God bless you

Dear Sir:Follow the instruction 1) Instruction manual about the waxed 2) Run the software calibration for diagnose and troubleshooting. If you do not have instruction manual download from Lifefintess.com or fitness.manualsonline.com or www.iconservice. or www.retrevo.comGod bless you

see the following video and proceed according:God bless you

Dear Sir:Please adjust the reed switch, clean, and tigh the connector very well.See the diagram attached. Run after you fix the software calibration.for diagnose, troubleshooting.sincerely. God bless you.

If the console takesbatteries, replace them. If this does not work or your console does not requirebatteries, check the reed switch or optic sensor. Reed Switch:Unplug the treadmill and remove the motor hood cover. The reed switch is mountedon the frame next to the front roller pulley. There is a magnet glued into thefront roller pulley. When adjusting the reed switch, make sure it is pointingdirectly at the magnet. Move the tip of the reed switch within 1/8" of themagnet. Also, check to see that the wire is not damaged, and is connected tothe console. Then tight the flexible cords from keypanel vs display board( clean the keypane with spray from contact cleaner. then tight the connector from display board vs main motor controller. Remember the main motor controller has aprox 90% of functions of any treadmills. See the block diagram that I did for people like you, And now you will get powerful strong resultant what is wrong. sincerely. Good luck.finally 2 options: 1) display faulty 2) Main motor controller of course after you did the first step.