Ranger RCI-6900F-25 CB Radio - Answered Questions & Fixed issues
Audio chip superstar 3900 rx
toshiba ta-7222ap (8 leg IC on side of chassis same side as volt reg and power plug)
1/10/2016 12:06:28 AM •
Ranger...
•
Answered
on Jan 10, 2016
•
160 views
How do i adjust the sideband
Instructions
Connect one end of your coaxial cable to the output port on your SSB
Transmitter. Connect the other end of the cable to the coaxial input port on
your RF demodulator.
Connect one end of your 1/4 inch audio cable to the audio output port on
your RF modulator. Connect the other end of the audio cable to the audio input
jack on your amplifier.
Turn on your SSB transmitter, RF modulator and amplifier. Adjust your
SSB transmitter modulation by adjusting the knob on your RF
7/22/2012 12:11:18 PM •
Ranger...
•
Answered
on Jul 22, 2012
•
250 views
My 2950 transmits on 1 channel higher when first
the radio needs to be aligned. The VCO may be unlocked.
What ever is not in alignment is off ever so slightly so that when you turn it on, its off freq, but once it warms up it is on, because some parts will slightly change values due to heat or temperature change.
It may also be a resistor that is loosing its value some where in the mixing circuit. Its off until it gets warm because it is going bad.
If you know what you are doing you can track it down with an ohm meter. Each color code is a different value. If the resistor is not what the code says it is, then there is a problem.
You should take it to a tech to have it aligned. In most cases, because its of and or the VCO is off, it can drift until its been aligned again and the VCO is locked up.
4/29/2012 11:21:01 PM •
Ranger...
•
Answered
on Apr 29, 2012
•
137 views
I have a 6 wire D104 . How do I wire it to a Ranger 2985 dx ?
Wiring a 6-wire D104 microphone to a Ranger 2985 DX requires connecting the wires in the correct order and configuration.
The Ranger 2985 DX has an 8-pin modular plug, and the D104 microphone has a 6-pin modular plug.
Here's one way to wire the D104 microphone to the Ranger 2985 DX:
- Connect the red wire from the D104 to the 8-pin modular plug's pin 4 (PTT - Push-To-Talk).
- Connect the black wire from the D104 to the 8-pin modular plug's pin 5 (Ground).
- Connect the white wire from the D104 to the 8-pin modular plug's pin 6 (MIC + Audio).
- Connect the blue wire from the D104 to the 8-pin modular plug's pin 7 (Receive Audio)
- Connect the green wire from the D104 to the 8-pin modular plug pin 8 (Transmit Audio)
- Connect the yellow wire from the D104 to the 8-pin modular plug's pin 3 (UP-Down).
It's important to double-check the wiring configuration with the user manual of the Ranger 2985 DX and the D104 microphone. Some manufacturers have different wiring configurations and it's important to match the wiring accordingly to avoid any damage to the device.
It's also worth noting that if you are not comfortable with the wiring process, it's best to consult with a professional technician or a radio expert.
1/28/2023 12:45:23 AM •
Ranger Radio...
•
Answered
on Jan 28, 2023
•
109 views
Led display
Hi John,Ranger CB YES, Model No. NO, led display, YES IT HAS ONE OF THOSE.More info please john.The more info about the radio you give and the problem, the easier it is to give you assistance, we can't answer buy guess work, it's neither helpful nor pleasant.Cheers,Peter
12/4/2022 7:46:51 PM •
Ranger Radio...
•
Answered
on Dec 04, 2022
•
84 views
Not finding what you are looking for?