Top 20 Timex 27191 Wristwatch Questions & Answers

Hi Janet, Follow this link. https://www.youtube.com/watch?v=WBPD80zQPRYOr smear some washing up liquid around the rubber ring on the back part.Hope this helps.Kind regardsDavid

Go to your local hardware store and get a Dremel tool or a generic rotary hobby tool. They have buffing wheels and buffing compound that you can buy. Then apply some of the buffing compound to your buffing wheel and carefully buff your etching. Remember to re-apply buffing compound regularly when buffing.

I'm sure it is low batt.. replace a new battery and it works properly again.. i'm happy that i have been help you..

You could get one on ebay, and most department stores will also carry them.

glue it back.

hi

I appreciate your line of thought concerning the problem of your watch.

like you rightly mentioned before, it could be a battery prob;em which is usually the commonest for this error. so please change the batteries first then if the problem persist a simple service of the watch should solve the entire problem.

all the best

pull the crown to its middle position then turn the crown until it reaches the exact date then push the crown to finish. i hope that i had been helped you.

probably it is not broken, it is only detached. bring it to watch service center they can immediately attach the minute hand. i hope i had been helped you.

That is what Timex does, they usually never repair the watches only send a similar replacement watch. Did you try to call them and notify them of the problem? The phone number for timex product service is 1-800-448-4639 or 1-800-367-9282, they should have at least notified you they were sending a replacement. Sorry about your trouble hope this helps.

the jeweller must have it, but if he does not have the glass, tell him to find a glass for you. he probably know where to find in your location. he must be the one to find it for you... i hope this thing will help you.

you must replace a new battery for your timex watch. bring it to watch expert for the caseback is not easy to close by hands only. your watch battery is CR1216. i hope i had been helped you.

Hi there,

Usually these kind of watches does not indicate if you are on PM or AM.

My hunch is that when you set the time and it goes pass 12AM the watch thinks that it's just 12PM so it does not change the day. Technically you are 12 hours behind.

To set things right try moving the dial until the hand reaches full circle and it changes the date.

once it does it will give you a hint wether you're on AM or PM so you can set it back to the correct date and time.

Hope this helps!

Actually all the hours are military time. They are the same for the first twelve hours of the day. If you go through the setting procedure it will ask you if you want "12" or "24" hour time. Select 12. "24" is military

A jeweler's press provides an equal amount of force around the edges of the watch back without putting that same pressure on the watch crystal (which could cause it to crack or break). If you have a flat crystal, you might have success in putting the watch between two pieces of wood and using a regular vice to very gently push the front and back together. However, you risk doing damage to your watch crystal.
Your safest bet may be to go to a jewelry store or jewelry counter in a department store and ask if they could close the back for you with the proper tool. You may have to tip them a few dollars, but that is still far cheaper than the cost of replacing a broken watch crystal.

Any watch repair shop will do that.

if your 1440 timex watch has a set button, press and hold it until some of the digits blinks and the one that blinks can be adjusted. but if your watch doesn't have a "set" button, press and hold the "mode" and it turns to 0 00 press it again and the time blinks and you can set it. if you like most accurate solution please give me the model no. of your timex watch. thanks!

the date wheel of your watch has a problem, it has to be fix by timex watch technician. or someone that is good in handling a timex module.

Price: $60.00

Insane as it seems, apparently the Indiglo wr30m watch stem does NOT have either a set screw or a release button. No vice needed though, just good fingernails. Pull it out one click to the 'set time' position and pull it out some more and it comes out.

The middle position is usually used for changing the day and the date.

Turn it clockwise for one and anticlockwise for the other.

The fully out position usually stops the watch and is used to set the hands.

As you rightly observe, there are not many other options!

I assume that your haven't got any instructions for your watch so if the above does not solve your problem, then you can get instructions from the Timex web site "timex.com".

At the bottom of the screen click on "manuals/downloads", then on "product
manual download"

Enter your watch type in the search box and click on "search"