Mrs.Sarah Kim, prestar seria mente los
individuos. Le doy crédito de 3%, no menos $ 5,000.00 y por encima de $
100,000,000.00. Contacte con nosotros ahora con esta información a
continuación: Préstamos Personales (Secure y ordinarios) Nombre y
apellidos:. PAíS Ubicación: SEXO: EDAD: El número requerido para
el crédito: Propósito del préstamo:. La duración del
préstamo:. Teléfono:. Mrs.Sarah Kim [email protected]
Get a RCA cable and connect from your amp where it said Sub Woofer in the Pre Out box in the back of the amplifier top left hand side and take it to the "Sub In" located in the back of your Sub woofer bottom right hand (White round connector).
Good Luck!
Transistors are transistors regardless of the make of equipment they are in. Printed on the transistor is the value of it. Most electronic retail shops (Jaycar) will have a replacement unit.
First of all remove the surround speakers and using a AA cell check if there is noise which will confirm the speakers. now it is important that the surround is activated, so play a DTS DVD and select for the surround. If there is no sound from the speakers though the connection is given correctly then it is fault on the surround amplifier.
You can activate the TEST on the amplifier and listen if all the speakers are activated and calibrated. If not the fault can be the sound processor or the ouput.
In both cases this wwill require that the signals are traced on the board. Since these are highly populated boards placed with vertical slots , to probe might require JIGS to loop connection or the boards cannot be checked on circuit. Also ONKYO will refuse to take amplifier for service if it is tampered and so unless you are equipped properly it is not advisable to probe or tamper.
All what can be done is to remove the boards and look for possible break in connections/connectors, check the surround amplifier power supply , check the main processor connector outputs.
If not refer to Onkyo for an estimate.
Dit betekent dat de versterker een fout heeft opgemerkt. een aantal oorzaken zijn als volgt: - een te hoge temperatuur, dit zou na een half uur afkoelen zijn verholpen. - interne software fout, deze zou na 5 min zonder spanning verholpen zijn. - een kortsluiting in (een van) de luidsprekers, alle luidsprekers loskoppelen kan zekerheid bieden. - een defecte stuur of eind trap.
helaas is in de praktijk het laatste de meest voorkomende oorzaak en dient de versterker te worden gerepareerd.
Not worth repairing until the root cause of the failure is proven.
The reason being is that you can have it happen again if caused by any of the devices attached to it, such as inefficient speakers.
The fan in those Audio System only turns at about 1/4 to 1/3 of the ride of your volume control.
It had been intentionnaly designed like that, to achive a quiet operation at low hearing volume.
But if the fan don't move by cranking up the volume at 1/2 to 5/8 of the volume control (with speakers on). You need to have the fan or the fan power circuit checked by technician.
Spider Guy
Some blu ray disc play fine. Others play the menu music, but when the feature starts, the sound disappears completely. And then others don't play music at all, no sound what do ever.
The flash probably was a small resistor burning. While not particualrly common, it does happen. The output transistors are shorted and need to be replaced. If the same channel is bad as the first time, there is a possability that the unit was not completely repaired. Some shops only change the shorted transistor within the transistor pair. This is poor practice and usually leads to another failure of the same channel Check your previous invoice for the parts replaced. The entire complimentary pair of output transistors should have been replaced. If only 1 iof the 2 were replaced, you may have an argument for a warranty repair.
yes , Im afraid you have a chip gone , If you open the unit up you'll see a alloy heatsink with 4 to 8 large chips screwed to it , These are the amp drivers , In between these chips you see a smaller one (that is the protect chip),You see when things get a little hot this chip is designed to break sooner that the more expensive main amp chips , In the past ive unsoldered these and still found the amp driver bust too ,dont worry though , maplins or even farnell(cpc) on the web will supply these for less than a tenner..If you wanna test my fix then just unsolder the littlest chip on the main heatsink and it should start to work again but with NO protection(unplug it first before taking it to bits)