20 Most Recent Citizen Skyhawk Eco-Drive JR306059F Wrist Watch - Page 5 Questions & Answers

an Eco-drive does not have a battery, it has a rechargeable power cell that is charged by light through the face of the watch. If you have replaced this cell you may have damaged the watch. If the cell was not soldered in, replace it and put it under a fluorescent light for a little while (several hours) and it should start working.

http://www.citizenwatch.com/COA/English/faqs.asp?topic=Eco-Drive

http://www.citizenwatch.com/COA/English/rechargeguide.asp

http://en.wikipedia.org/wiki/Eco-Drive

The answer just depends on your preference: you can use a glass to glass adhesive and it should hold up fine. Just make sure that when you are attaching the crystal it is in the exact spot you need it to be in and also to have a small clamp ready to press over it. This will help to seal it better and make it last longer. If you don't feel up to it, I would take it by and let a jeweler take a look at it. Either way it's going to be a small fix. Hope this helps!
FlamePants

Hi Hennie. Je moet de zomertijd op automatisch zetten. Ga naar http://www.citizenwatch.com/COA/English/settings_int.asp?caliber=U600&interactive=U600
Groeten, Jaap

The watch probably needs re-charging.

Go to http://www.citizenwatch.com/CUK/English/rechargeguide.asp, fill in the details of your watch and read the instructions.

Pull out the side round piece. Then turn it backwards. This should work. It might be two notches out, instead of pulling it out once.

You can get instructions from the Citizen web site.

Go to "citizen.com" and on the upper right there is a menu. Click on "technical
support" and then on "setting instructions"

Fill in the information required from the back of your watch and then click on
"get setting instructions"

OK try and follow these steps and it may help you set the time on your Watch. Once you understand the different function buttons on the edge of the case setting the time will be an easy task.

1-Note the 2 and 4 o'clock function buttons and the crown at 3 o'clock on the case edge of the Citizen Skyhawk Eco-Drive. These buttons set all functions of the watch.

2-Set the home city digital display function at 9 o'clock by pulling the crown to the first position. Rotate the crown until the mode hand in the subdial at 6 o'clock is aligned with TME. Press the 2 o'clock button until the nearest major city where you live appears. Press the 2 and 4 o'clock buttons at the same time to find the home city in the 3 o'clock digital display window. Once the city is selected, the time is automatically set by the automatic radio reception function.

3-Pull the crown out to the first position to manually set the time. Rotate the crown until the mode hand is aligned with the CAL, TME and RX-S position under the umbrella line. Push the crown flush with the case edge. Point the watch's 9 o'clock side in the direction of the radio transmitter. For example, if you live in Los Angeles, point the watch's 9 o'clock side east towards Ft. Collins, Colo., where the transmitter is located.

4-Hold down the 4 o'clock button for two seconds until the tone sounds and the second hand stops at the RX-S position. The second hand will then move to H, M or L found at the 2 o'clock subdial. Remain holding the watch in the same position. The second hand will move from the H, M or L position with the hour and minute hands to the correct time once the radio reception is completed.

5-Press the 2 o'clock button to start the chronograph's stopwatch. Press the button a second time to stop the timer. Press the 4 o'clock button to reset the timer.

6-Pull the crown all the way out and rotate it clockwise until the correct date is selected. Push the crown flush when finished.

IF you are still not able to set the time contact your dealer or the nearest Citizen showroom.

Just found someone else's comments on the watch. Read them carefully and you will find not only how to set the time but many other things as well.
http://www.epinions.com/review/Citizen_Skyhawk_Eco_Drive_JR306059F_Wrist_Watch/content_213123698308
And follow the link below to search for things on the internet in future
http://www.fixya.com/support/r3812010-search_drivers_online

You can get instructions from the Citizen web site.

Go to "citizen.com" and on the upper right there is a menu. Click on "technical
support" and then on "setting instructions"

Fill in the information required from the back of your watch and then click on
"get setting instructions"


or

Go to "citizen.com" and click on "watch finder".

Put your watch model into the search box on the left and click on
"search".
Click on the watch to view details.
On the right is a small menu, click on "get technical info"

Look where the band connects to the fold-over clasp. There are several holes on the clasp. Use a plastic headed thumbtack or some other small pointed object to push the pin in and move to desired hole to fit your wrist.
If the longest adjustment is still not big enough you will need to add a link to the band. You can contact Citizen Watch at 800-321-1023 they will send you 3 links at no charge.

Here is how to correct the 0 Position for your watch.

While your the crown of your watch is down in the starting position , turn the crown until the mode hand (this is the circle at the bottom of the face) reaches CHR

At this time now pull out the crown until it clicks two times, two the second setting of the crown.

This will bring the watch to the 0 position correction function.
you can turn the crown clock wise to correct the hour hand.

press the a button to switch hand to second, or press again to switch to minute. Then use crown again to correct 0 position.

The hour and the 24 hour hand is in conjunction with each other.

then push down the crown all the way in and you should be all set.