At your Elna dealer, at just about any sewing machine repair service, or if you don't have one locally, try Ron Anderson at A1 Sewing:
[email protected] I've known him on the net for about 20 years, and he's quite helpful.
Make sure power is turned off. Get a pair of pointy nose pliers (may need to try a couple of sizes to get correct one). Use these to get hold of the metal light base and remove. Will probably need to turn base to release. Then insert new bulb.
Make sure power is turned off. Get a pair of pointy nose pliers (may need to try a couple of sizes to get correct one). Use these to get hold of the metal light base and remove. Will probably need to turn base to release.
I can't see one for the 945 but the above manual may give you some guidance as to what the replacment involves.
945 is a fairly new model so you may find that taking it to a pro and getting the timing and loopers checked at the same time is worthwhile. Also being computerised model, if you get something wrong and the computerised part is affected it could turn out more expensive to then take it to an Elna dealer.
I get my Bernette serger serviced every 2 years and it is now over 19 years old, and still performing well.
Thread the lower looper like normal, and you needle. When the upper looper comes up it will push up the lower thread and then you can put it under the pressure foot torward the back and start to serge.
Is the tension on the left needle on its normal setting and is the thread feeding okay to this needle, not caught up somewhere on the aerial or around the cone?
You could try unthreading everything, changing the needles, then rethreading the machine again in the sequence of the threading diagram and test sew.
However, if you have had this machine for a while and are very used to threading it and this seems like a fault to you, then it could be that the looper has been knocked out of timing and it would need a trip to the sewing shop to investigate further.
try this link http://www.youtube.com/watch?v=bC-bJE5zwzw&feature=related for movie of a Pfaff piping foot in action, the principal would be similar, you are wrapping bias strip around cording on left of foot and overlocking right side. You can also do this with fabric top and botton thereby inserting the piping as you make it.
I have not tried this technique myself as I've only bought a blind hem foot for my Bernina but must admit I have used that a bit in the past.
Most serging techiques are very similar across the brands.
It sounds like there might be an issue with the settings or mechanism of your Elna Stitch Craft 4000 sewing machine. Even after adjusting the stitch length, if it continues to sew very small stitches, there are a few things you can try:
1. **Check the Stitch Length Dial**: Ensure that you are adjusting the stitch length dial correctly. Sometimes, the dial may not be turning properly or may be stuck, leading to the machine sewing at the same small stitch length regardless of your adjustments.
2. **Clean and Oil the Machine**: A sewing machine that hasn't been cleaned or oiled in a while can have issues with stitch length consistency. Follow the manufacturer's instructions to clean out any lint or debris from the machine and oil the necessary parts.
3. **Inspect the Feed Dogs**: The feed dogs are responsible for moving the fabric through the machine. If they are not functioning properly or are obstructed, it can affect the stitch length. Check for any debris or damage to the feed dogs and clean or replace them if needed.
4. **Check the Bobbin Tension**: Incorrect bobbin tension can also cause irregular stitch lengths. Make sure the bobbin is correctly threaded and that the tension is adjusted according to the machine's specifications.
5. **Test with Different Fabric and Thread**: Sometimes, the type of fabric or thread being used can affect stitch length. Try sewing on different types of fabric with different threads to see if the issue persists across various materials.
If none of these steps resolve the problem, it may be necessary to have the machine inspected and serviced by a professional technician. They can identify any underlying mechanical issues that may be causing the small stitch length problem.
Question edited for clarity, add maker and '(what it is)'.
Question moved from Refrigerators category.
No, all finished. You might get one on eBay, set Watchlist.
https://www.google.com/search?q=Elna+Funstyler+3003FS
..
Question edited to fix the autocorrect.
The backup battery needs replacing.
The btr message means your battery backup is going bad and you need to change it. Tip the machine back, and on the bottom right there's a battery compartment for 2 AA batteries. Just put in new ones and you'll be set to go!
Quiltingboard Forumshttps://www.quiltingboard.com > Main
Jul 15, 2019 - I think the lever above the stitch length knob is for temporary reverse. The knob has red numbers and black numbers. The red numbers are for ...
Missing: 6500 key
