20 Most Recent Brother PE770 Computerized Sewing Machine - Page 9 Questions & Answers

You can download required manual from this page Home Sewing Machine ' United States ' Brother support website

The manual may be helpful: Brother CS 8072 Operation Manual be sure to ALWAYS RAISE the presser foot when threading the top thread. How to Thread Brother CS 8072 Sewing Machine eHow http://support.brother.com/g/b/faqend.aspx?c=us_ot&lang=en&prod=hf_cs8072eus&faqid=faqh00000485_000

It is a skilled job and best left to a service tech, but here is the service manual and some videos.Page 34 refers.https://acmerevival.com/wp-content/uploads/2021/07/smM3000.pdf

need to check the hook timing. put it in zig zag, no fabric, turn the hand wheel to you slowly. check the needle when it is coming back up, is the hook picking up the thread? if yes continue to check the next side, so if you check the left side then check the right. if any side its not picking up the thread then the timing is off and need to be retimed

https://www.google.com/search?q=Brother+compal+ace+manual ..

Which model machine is this? Do you know roughly how old it is? This is so I can check what setup it has and if I can find an owners manual for it for you.

If you can remove the cover on the left side you will see the presser foot bar. On the bar there will be a screw that may be loose. Turn the handwheel until the needle is all the way down and lift the foot manually until just before it makes contact with the needle clamp and tighten the screw on the presser foot bar. That should do it.

Yes you are right, it is not available anywhere. If it was this specially crafted search link would find it. Lots of 1034D available. You would have to have one made if you have a broken one as a pattern. Or buy a Juki as suggested on Reddit. https://www.google.com/search?q=brother+serger+%221034dx%22+%22needle+plate%22 https://www.reddit.com/r/sewing/comments/sdkw99/need_help_finding_a_needle_plate_for_a_brother/?rdt=45300 ..

This is most likely a threading or a tension issue. Take out both the top and bottom threads. Clean all the areas you can get to, top and bottom, to remove any tiny pieces of thread and fluff. You'll be surprised how much trouble two or three little bits of old thread can cause. Re-thread the machine and check your tension settings. Are you using a different type/brand of thread, have you changed the needle or are you sewing a different type of fabric? These can all affect how a machine sews so you might need to adjust your tension settings.

I'd contact Brother. They have the best service department of any company I know. Been very helpful to me more than once. Site is here, just pick your country. http://support.brother.com/g/b/countrytop.aspx?c=ca&lang=en

Have you tried adjusting the bobbin tension? There's a small screw on the bobbin case so the bobbin can be adjusted. only turn the screw a little at a time. Also be sure your top tension isok. However if you still need help these days you can buy a new bobbin case and a new top tension, both will be adjusted already to use from the factory. don't let it drive you crazy they sell the preadjusted parts for us few that just want to sew not be a tech to just sew a blouse etc. I hope this helps. good luck Lynn

Question edited for clarity. "air conditioning or engine sounds"? You mean like the motor is running? It sounds like the belt has broken or come off the pulleys. https://www.google.com/search?q=brother+xr+35+replace+belt ..

It just needs cleaning and servicing (terrible sounds = lubrication). Parts seldom need replacing, it just needs tightening up. Service centres can usually get parts.

These are all the best parts suppliers. Did you try Brother direct? https://www.google.com/search?q=Brother+Pacesetter+PC+8200+parts ..

Didn't you just post as Anonymous? We are FIXYA dot com, we don't repair anything at all. We only supply information and we do that for free! We are not who you think we are. Click the link to find repair shops that are near you. https://www.google.com/search?q=knitting+machine+repairs+near+me ..

I have a single head 9 needle brother 416 embroidery machine does not change color.can someone help me with this problem

Question edited for clarity. They are normally screwed in from the front. Look for a screw under a cover in the knob. There is a Service Manual in this link. https://www.google.com/search?q=brother+pq1500+service+manual ..

To find the stitch count on a Brother Pacesetter PC-8500D, follow these steps:

1. Turn on your machine and select the embroidery design that you want to check the stitch count for.
2. Press the "i" button on the machine to access the information menu.
3. Scroll through the information menu until you see the stitch count option.
4. Select the stitch count option to display the total number of stitches in the embroidery design.

Note: Some embroidery designs may have multiple color changes or sections, so the stitch count may be broken down by color or section. You can navigate through these options using the arrow keys on the machine.

To check the stitch count on a Brother Pacesetter PC-8500D embroidery machine, please follow these steps:

1. Turn on your machine and select the embroidery mode.
2. Press the "Machine Information" key on the touch screen.
3. Scroll down to the "Stitch Count" option and select it.
4. The stitch count for your machine will be displayed on the screen.

Note: If you have reset the stitch count on your machine, the stitch count displayed will be zero.

Brother XR-31 Manuals - ManualsLib

https://www.manualslib.com > ... > Sewing Machine We have 2 Brother XR-31 manuals available for free PDF download: Manual, Quick Reference Manual ... Brother Innov-is 1000 Sewing Machines: Quick Setup.

Brother XR31 Support

https://www.brother-usa.com > support > xr31 Find official Brother XR31 FAQs, videos, manuals, drivers and downloads here. Get the answers, technical support, and contact options you are looking for.