Jura Capresso ENA 4 (13421) - Answered Questions & Fixed issues

On the A1 there is a sensor on the bottom edge of the panel showing the help phone numbers. On other models it may be located behind where the trip tray would be inserted. The sensor detects the presence of the grounds container. Take a paper clip and push up inside the notch holding the sensor. Do this with the machine on. The flap will be withdrawn and everything will fit back in.

Hi, I made a video how to fix your Jura step by step, good luck... http://fixandparts.wix.com/nicknicoloudis#!jura-coffee-machine/c15gy

remove tank clean with hot water, rinse and shake you should hear a rattle in the bottom of the tank. if you dont the the small black float built into the tank side wall is stuck. once free it will work fine.

As far as I know the Jura machines have a special oval shape screw head on their panels...and Jura charge something outrageous like 150euro if you want to buy the tool for opening these! Mite be worth trying to open it some other way like by gluing a tool or something into the head and let it dry, then open it.... then maybe replace the oval head screw with a different screw type when reassembling. Not an easy method of getting past the problem but id sooner do it than pay for the tool!!Hope this helps

Hi

The factory default setting is---

1 Cup - 5 OZ, high temperature and normal coffee flavor strength and 2 Cups - 5 oz. (per cup), high temperature with strong flavor strength.

You can adjust the settings of 1 cup from 0.5 to 8 oz. and 2 cups from 0.5 to 8 oz. per cup in strong setting.

Also please download the manual from the link and see the video therein for further information. Hope this helps...please post back for further assistance.

Daniel

This sounds like the grinder is not strong enough to grind properly. Try adjust the grind to a bit coarser, if this makes no difference then the bearings inside the grinder may gone. Try only fill a small amount of beans in the container and see if it works. It may be that when there is too much of a load on it it will not spin the blades.

Unfortunately, without being there in person to inspect the machine and its components, it's difficult for me to provide a definitive answer. However, I can offer some general guidance that may help:

1. Consult the user manual: The user manual for your Capresso C3000 should have a diagram or schematic showing the different components and their connections. If you still have the manual, check to see if there's a helpful diagram inside.
2. Look for visual cues: While it can be difficult to identify the tubes by sight alone, there may be visual cues that can help you narrow down which tubes go where. For example, one tube may be thicker or more flexible than the others, or it may have a different color or texture.
3. Experiment with different configurations: If you're unable to find a diagram or visual cues, you may need to experiment with different configurations until you find the correct one. This can be time-consuming and frustrating, but it may be the only option if you're unable to find any other information.
4. Seek professional help: If you're still unable to identify the correct tube configuration, you may want to consider seeking professional help. A qualified technician or repair service may be able to identify the correct configuration and get your machine back up and running.

I hope this helps, and I wish you the best of luck in getting your Capresso C3000 back in working order!

http://www.fixya.com/support/t12615678-capresso_303_will_not_steam

Talk him

The first thing to check is the seating of your water tank. Just a few grains of coffee grounds or dirt underneath the tank are enough to break the watertight seal. Make sure the area under the tank is absolutely clean. That's always worked for me when I've had the leaking problem.

Rinsing cycle at start up is electronically programmed function. Unplugging is a temporary solution. Jura will not sell parts or offer any guidance. I could look into more details to find an answer but the model Capressa 50 is not listed in my Data base. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edward_bbd2c7ff4ee1828a

TRY SWITCHING IT OFF AND RETRY LATER MAY BE IT WILL RESET IF NOT CHECK FOR ERROR OR TELL US MORE ABOUT THE FOULT

You really don't give which machine - but here is link to company product support. Maybe they will have product manual to help trouble shoot issue. Sorry could not of been more help Product Support

The switch or photo sensor is not sensing any beans present. So it can't continue Use torch to inspect bean entry area Small brush etc

Hi Marton Registered repairers love you guys.... If you carry a smartphone these days and most of us do. You need to learn to take photo's first. Even the Las Vegas pro restoration guy on TV does that. Sorry I don't have those photos and you'll be really lucky is someone on Fixya does. Try YouTube videos.

What model do you have? What's the problem you are trying to fix by resetting it?

Just a guess here but if you are not using soft water you may have a hard water scale coating on the sensor. The sensor is preventing the heating element from powering up because it thinks there is no water. Try filling the machine with vinegar for several hours (no more than overnight) This will dissolve hard water deposits and hopefully clear the sensor. (the sensor should be a simple continuity contact. If you can look inside and see a metal button and it is fouled clean it off.)

Try running distilled white vinegar through it.

constant heating message on screen is from a thermal fuse blown on one of the boilers. service call required i'm afraid...... very cheap part about 10 euro

Try applying hot water around the dish to expand and unstuck while gently but firmly pull the tray. It went in so must come out.