20 Most Recent Bosch WFVC5400UC Washer - Page 9 Questions & Answers

sounds like the thermal safety overload is cutting the power due to overheating hence why it just turns back on after a certain time, when the safety overload reaches a certain temperature it will cut the power to the machine or in some cases just the heating elements, once it cools down it resets and power is restored and by using the warm setting it obviously isn't as hot so its not overheating, its highly likely it is all blocked up internally with lint (i know it says self cleaning but they never work for more than a few years before requiring a proper clean and service)

It means that the water is not draining fromthe machine inthe time allowed by the controller.

1. Switch off the machine and disconnect the mains power.
2. Remove the filter and make sure that the filter is not blocked and is clean and clear of all debris. Clean as required. Note that depending on the machine type you may get a lot of water coming out of the filter when you remove it if the machine has not drained successfully. Note that if the machine has stopped and not fully drained then you may be able to drain out the excess water by removing or disconnecting the waste hose and laying it on the ground in a tray.
3. Proceed by checking the drain hose for proper connection and kinks and make sure that it is not blocked.
4. Also check that the main waste drain pipe, if you use one, is not blocked and clean if required.
5. Reconnect the power and switch the machine on.
If the problem persists then do the following.
6. Switch off the machine and disconnect the mains power.
7. Check the electrical connections at the pump and make sure it is operational.
8. Remove the connecting hoses, and expect water to drain out and make sure the pipes are not blocked with debris or any object blockage.
9. Makes sure the pump appears clear and that the impeller looks in good condition.
10. Reconnect the hoses and then reconnect power and switch the machine on.
11. If problem has not been corrected, then remove the pump and check that the drive coupling to the motor is OK and that the motor turns OK. If all is well then replace the pump.

check incoming voltage and heating elment

E 06 means slow or no drain//not a easy do it yourselfer machine//you will need to get to the pump might be plugged//for the do it yourself you can get to the back( but this won't be easy) most techs if they know the machine will take front of that takes pratice//anyhow take rear panal of you will see drain pump in there remove tub to pump hose most likely has some items inside//note some bosch washers have small pump drain hose to get water out before you remove pump hose/if it will drain do that first save alot of mess...........(((( check this first))) note some have round cover at lower bottom put pointy item in hole of cover turn to release ( it will turn hard) some also had cleanout behind that cover/ if so check pump from that location much easier then taking back of.....Hope this helped if it did please vote...if you need more help please ask ...good luck

Hi , could any know what F67 ERORR CODE FOR . IT KEEP SHOWING ON THE SCRREN MY WASHING MACHINE IS I XX8 BOSCH
Thanks

If your model is WFMC3301UC/06, the Main Control Board is: OEM Part # 00660809

CL indicates child lock has been activated. to deactivate it you need to press and holding the start button for 5 seconds.

Make sure the drain hose is not extended too long.

try this link http://howtomendit.com/answers.php?id=502630 Also try this https://www.youtube.com/watch?v=PvJlqOjG6Uc

Hi, I know it's kind of a silly thing but when loading the machine make sure nothing is jammed against the dispenser preventing it from opening. I've run into that a few times and people looked at me like I had two heads but when I showed up to look at the machine,it was loaded like thanksgiving dinner was just over. If that is not the issue then it's either the dispenser itself that is broken or it's not getting power from the board. Either problem will require getting into the door of the machine and running a test program. I would call a local appliance repair company as these tests require the machine to be powered up and specific tools. Hope that helps.

https://www.bosch-home.com/us/supportdetail/product/SHP65T56UC/07 https://www.bosch-home.com/us/owner-support/contact-us

I get paid over $180 per hour working from home with 2 kids at home. I just got ypaid $ 8550 in my previous month It Sounds unbelievable but you wont forgive ourself if you don't check it..... http://www.Geosalary.com

Check that the load is within the 6kg limit and not entangled into a ball, which will unbalance the drum. Separate the items and try again. I believe Bosch has a telephone help line.

Original advice in 2014 from Kenjo, on another website: f21 is worn brushes in the motor replace them and to reset the f21 code.... close the door, turn timer dial to position 8 going clockwise, hold in the spin speed button whilst turning dial to position 9 let go of spin speed button and return dial to off position.

Probably a blocked or faulty internal inlet valve; check the feed filter which is visible inside the valve.

Try ManualsLib.com if you cannot find one from the Bosch Customer assistance site.

check the board fuse with a multi meter

the most common problem is the motor brushes have worn out,so motor needs to be removed and new brushes fitted

unplug machine You will need to check the water level censor on the back of the drum,remove rear panel look for a small plastic pipe remove it and blow gently into it you should hear a clicking sound to indicate that the censor is working clean out the small pipe with a ear bud or similar,replace and run machine. eric992

Go to Bosch site purchase service manual eric992