20 Most Recent Sony KDL32BX300 32 in. TV - Page 2 Questions & Answers

HelloPart Number for 32" LCD panel is [1-811-059-11] (S32TSP)Part Number for 40" LCD panel is [1-811-060-11] (S40TSP)

Tries tv and those Cables,Satalites or Telicoms pay boxes unplug,replug it back like about an hour later.Ur tv now should do a resetting itself back to the factory setting.Those pay boxes will reboot and updated it softwares.Ur tv should have incomming broadcasting tv chanels signal know.If u still have the same problems call ur tv Cables,Satalites or Telicoms compannies for a fix.

Hello, you need to make sure what is broken, the remote control or the TV. To check the integrity of the remote control, you need to broadcast from the remote control while he aimed at the video camera. If you see a flicker of light through the camera it shows the integrity of the remote control. In this case need to fix the circuit of the infrared receptor. If the remote control out of order can be opened carefully by a thin screwdriver, usually the causes to the error are loose components or contacts that are supposed to weld back into the board. I hope it was helpful!! let me know if you need further assistance.

Hi there,

You need to reset the TV to factory defaults, then run through the initial setup again and make sure you choose HOME and not RETAIL as the location on the second screen of the setup.

To reset the TV to factory defaults:

1. Switch on the TV
2. Hold down the UP arrow key on the Sony remote control
3.While stillholding UP, press the POWER/STANDBY button on the front of the TV once.
4. Release the UP button

The TV will switch off and back on again. You will lose all of your settings and you will need to run the automatic channel scan again, but you will be able to select HOME as the location this time.

Please note: This question is listed for Sony TV model number KDL-32BX300. If you have a different model the reset method may not apply to you. In this case, try it once and if it doesn't work, please post back with the correct model number.

Hope this helps - please reply to me from within this page if you need further assistance.

Regards,
BElectric

Try the following links:

http://esupport.sony.com/CA/perl/model-home.pl?mdl=KDL32BX300&LOC=3

http://esupport.sony.com/CA/perl/model-documents.pl?mdl=KDL32BX300


This one is a direct link to the User's Manual:

http://www.docs.sony.com/release/KDL22BX300.pdf

Good luck and please comment back and RATE if this was helpful.

Tries tv unplug,replug it back about an hour later.The tv now is resetting back to the factory setting.The tv should be working again now.If have the same result.The tv power supply board is the causes and the problems.That the board,where the power a/c cord plug into it.Tries websites like Shopjimmy.com,Ebay.com to buy a refurbish power supply board for the replacement.

Hi,

Yes you can. If it's exactly 4 hours, then you need to change the "Eco" power settings as follows;

1. Press the "MENU" button on your Sony TV remote control.
2. Use the circular arrow keys on the remote to highlight the flower icon for the "Eco" settings:


3. Press the large "+" key on the remote (in the centre of the arrow keys) to open the "Eco" menu.
4. Use the DOWN arrow button to highlight "Idle TV Standby". (The current setting will be 4h)
5. Use the LEFT/RIGHT arrows to set the value to "OFF" (1h or 2h can also be set).
6. Press the "MENU" button again to close the menu and return to watching TV

Hope this helps. Please post back if you are still unable to disable this feature or need further assistance.

Regards,
BElectric

have you hooked the yellow to yellow and the red to red and the white to white that should fix your issue

Defective set. I would return it immediately.

I would try a new T-CON board first.

The problem in most of the case are: 1. Interference from a defective fluorescent lamp at your room sending signals to the infrared receiver of the TV. 2. Defective infrared receiver itself that sending noisy control signals to the CPU. 3. Defective manual control withes it has leakage. 4. Water damaged control switch PC board.

Do a reset to this TV, and then check. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/ Service mode entry, adjust and exit procedure to many popular brand TVs are given. Never forget to exit the service mode, after all adjustments have been done.

Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electro-medical.blogspot.com/ http://homenol.blogspot.com/ http://electronicshelponline.blogspot.com/

Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis. http://electronicshelponline.blogspot.com/ To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced. To some models of sets, all these section circuit will be integrated at its main board. If this is the case, you have to replace the main board....