Jabra Stone Bluetooth Headset - Page 8 - Answered Questions & Fixed issues

If your FT-747GX is not transmitting when you press the PTT button, there are a few things you can try to troubleshoot the issue:

1. Check the settings: Make sure that the transmitter is set to the correct frequency, mode, and power level. Also, check that the mic gain and RF power settings are adjusted correctly.
2. Check the antenna connection: Make sure that the antenna is properly connected to the radio and that there are no loose connections.
3. Check the power supply: Make sure that the radio is receiving adequate power and that the power supply is functioning properly.
4. Check for software updates: Make sure that your device has the latest software updates installed.
5. Check for interference: Make sure that your device is not too close to other electronic devices that may be causing interference.
6. Check the values of the voltage on the main board, as you mentioned, the values of 4.5 and 0 for RX and 0 and 1.4 on TX, it could be possible that one of them is too low or high, which can cause the issue.
7. Check the PTT switch, and make sure that it is working properly and not stuck.

If none of the above steps resolve the issue, you may need to contact the manufacturer or a professional technician for further assistance. It's recommended to check the user manual of your device before trying any of the above steps, as the process of troubleshooting a transmitter can vary depending on the model and manufacturer.

If the PPT (Push-To-Talk) button on your Rino 650 is not working, there are a few things you can try to troubleshoot the issue:

1. Check the battery: Make sure that the battery is fully charged and properly installed in the device.
2. Check the settings: Make sure that the device is set to the correct frequency and that the PTT button is configured correctly in the settings.
3. Check the physical button: Make sure that the PTT button is not stuck or damaged in any way.
4. Check for software updates: Make sure that your device has the latest software updates installed.
5. Check for interference: Make sure that your device is not too close to other electronic devices that may be causing interference.
6. Check the programming: Make sure that the device is properly programmed with the correct settings, including the correct channels and frequencies.
7. Check if the device is in a low power mode, if so, switch it to high power mode.

If none of the above steps resolve the issue, you may need to contact the manufacturer or a professional technician for further assistance. It's recommended to check the user manual of your device before trying any of the above steps, as the process of troubleshooting a PTT button can vary depending on the model and manufacturer.

It sounds like you are having an issue with your GP339 radio where the PTT (Push-To-Talk) switch is not transmitting when pressed. Here are a few potential solutions to try:

1. Check the battery: Make sure that the battery is fully charged and properly installed in the radio.
2. Check the antenna: Make sure that the antenna is properly connected and not damaged.
3. Check the settings: Make sure that the radio is set to the correct frequency and that the PTT switch is configured correctly in the settings.
4. Check the microphone: Make sure that the microphone is properly connected and not damaged.
5. Check the programming: Make sure that the radio is properly programmed with the correct settings, including the correct channels and frequencies.
6. Check for physical damage: Make sure that the radio does not have any physical damage, such as a broken switch or damaged wiring.
7. Check that the radio is programmed for the correct channel.
8. Check that the radio is not in "Low Power" mode, if so, switch it to "high power" mode.

If these steps do not resolve the issue, it may be necessary to contact the manufacturer or a professional radio technician for further assistance.

There are a few things you can try to troubleshoot this issue with your 2013 Chrysler 300c's Uconnect Bluetooth system:

1. Make sure that your phone's Bluetooth is turned on and that it is in pairing mode.
2. Check the Uconnect system's settings to ensure that Bluetooth is turned on and that it is set to discoverable mode.
3. Try restarting both the Uconnect system and your phone to see if that resolves the issue.
4. Check the vehicle's manual to see if there are any specific instructions for pairing a device with the Uconnect system.
5. If the above steps don't work, try clearing the Uconnect system's memory of previously paired devices, and then try pairing your phone again.
6. Check if the software of the Uconnect system is up-to-date, if not update the software.
7. Try deleting all previously paired devices on the Uconnect system, and then try pairing your phone.

If none of these steps resolve the issue, it may be a problem with the Uconnect system itself and you may need to take your vehicle to a Chrysler dealership for further assistance.

If your TVBP-BTN wireless stereo headset is not charging properly and the blue light is not showing, there are a few things you can check to fix the problem.

1. Check the charger: Make sure that the charger is functioning properly and that the connections are secure. Try using a different charger or USB port to see if that resolves the issue.
2. Check the charging port: Make sure that the charging port on the headset is not dirty or blocked. Clean it with a dry cloth if necessary.
3. Check the battery: Make sure that the battery is not damaged or dead. If the battery is damaged or dead, the headset will not charge.
4. Check for software updates: Make sure that your headset's firmware is up to date, if there is any updates available, install it.
5. Check the manual: Check the manual that came with the headset for any troubleshooting steps or contact the manufacturer for further assistance.
6. If you have tried all of the above and the problem persists, it may be a hardware issue, and the headset may need to be repaired or replaced.

Hello Coralee SW5 in London? Greetings from Toronto, Canada, but my in laws lived in NW5. I moved here from Cornwall in 2005. Did you mean BeoSOUND as opposed to BeoPLAY? There is a short video on opening the doors. Page 8 of the manual below shows the have be fitted, so conversely, they can be removed. https://www.google.com/search?q=B+%26+O+Beosound+3000+glass+doors+will+not+open These are the Bang and Olufsen outlets in London https://stores.bang-olufsen.com/en/united-kingdom/london and finally, there is a repair partner in Eastbourne https://www.av-services.co.uk/bang-olufsen The manual if you need it. It is an elderly system and only does what it does, music and tuner. https://bangolufsenassistentgohe.blob.core.windows.net/manuals/SOUND_SYSTEMS/BEOSOUND_3000/BS3000_RB_EN.pdf . If you need further help, click Comment below. ..

Usually because the purchaser didn't read the instructions or because the instructions are badly written from Chinese. This is an eBay special. I wrote this Tip on connecting Bluetooth devices which mentions the step that is always missed. https://www.fixya.com/support/r26362721-pairing_bluetooth_devices

iEssentials Bluetooth FP1 Headset, USB Car Charger ...

https://www.ebay.com > itm iEssentials Bluetooth FP1 Headset, USB Car Charger Included ( IE-HFBLU-FP1 ) · Item Information · Item specifics · Shipping and handling · Sales Tax for an item # ... US$12.95 · ‎In stock

Setting up the frequency on the radio is quite simple. It is nothing more than adjusting the UHF and VHF settings to compensate for the curvature of the earth.

It appears you can. Normally you load the software to the new PC and then copy the data file to USB and transfer it. It would be a file in USERS. Then reboot the computer. https://www.google.com/search?q=gs3000+scanner+on+one+PC%2C+transfer+that+data+to+a+new+PC ..

no factory reset --this is user manual page 36 is trouble shooting ----https://www.manualslib.com/products/Radio-Shack-Pro-135-3101070.html

Contact Relm directly to request the manual.

refer to instructions that came with unit, if you lost them google your model number manual. copy and paste https://www.fixya.com/support/t24668314-remove_entire_cutting_head_homelite_hlt ..

" of YOUR NTE1197 ". Nope we are Fixya dot com, so you have nothing of ours. Contact them, we are not they. https://www.google.com/search?q=nte+1197 ./.

Check the PA circuit. If an aerial was not connected or has a very high SWR, it will cook the output section.

The blinking light tells you it is on and working it is also part of the setup process The only two ways to stop it blinking is to shut down the headphones or dismantle the headset and disconnect the led

Hi, please reach out to your products manfucaturer and ask them to email you the diagram. Thank you.

As a licenced HAM Radio opperator, you will be aware of the legalities and the frequencies you are allowed to use. What is your question I wonder . ..........................................

This unit looks to be a AC/DC PA amplifier. Here's an owners manual if you don't have one. That and a parts list is about all I could find. Mike http://support.radioshack.com/support_audio/doc73/73142.pdf

1. Go to your Phone's home screen and find the "Settings" icon. 2. Click on the "General" button under Settings. 3. Find the "Bluetooth" option and slide it over to turn the function on. 4. Your iPhone should find the device once this is enabled and should show the device name on screen. When it does that, you will need to hit the "Pair" button in order for the devices to sync. You may need to enter a four-digit password, which is provided with your wireless device. 5. Once that is entered, hit "Connect" on your iPhone to complete the setup. Your headphones should now be working properly. You'll have to look up specific instructions for your device by searching the model number. The pairing code will likely be 0000 or 1234