Top 20 Jabra BT650 Bluetooth Headset Halo - Page 6 Questions & Answers

It sounds like there may be a problem with your Walkie Talkie's display. The "E" and "O" symbols you are seeing could be error codes indicating an issue with the device's internal circuitry. The "E 02" code could indicate a low battery or a problem with the device's power supply. The "O FF" code is less clear, but it could potentially be related to the device's frequency or channel settings.

1. Check the power supply to the repeater to ensure it is plugged in and working properly. 2. Check the antenna connections to ensure they are securely connected. 3. Check the coaxial cable connecting the antenna to the repeater to make sure it is free of any damage or degradation. 4. Check the settings on the repeater to ensure it is configured correctly for the channel. 5. Check the radio frequency of the repeater to ensure it is correct for the channel. 6. Check for any interference in the area that may be causing the repeater channel to fail. 7. Check the signal strength of the repeater to make sure it is strong enough to transmit the signal. 8. If possible, try another repeater in the same area to see if it is having the same issue.

Usually bad connections or shielding on the microphone. https://www.google.com/search?q=texas+ranger+base+station+buzzing+noise ..

I can suggest some resources that you can use to find the frequencies you're looking for. One option is to check the website of the Chippewa County Sheriff's Office or the local government website for information on radio frequencies used by their departments. Another option is to visit the website of the Federal Communications Commission (FCC) and use their online database to search for radio frequencies assigned to Chippewa County. You can also try searching for online forums or groups of radio enthusiasts or scanner hobbyists that may have information on frequencies used in the Chippewa County area. It's important to note that you may need a license or permission to use certain frequencies, and it's always a good idea to check local regulations and guidelines before using any radio equipment.

Hello Coralee SW5 in London? Greetings from Toronto, Canada, but my in laws lived in NW5. I moved here from Cornwall in 2005. Did you mean BeoSOUND as opposed to BeoPLAY? There is a short video on opening the doors. Page 8 of the manual below shows the have be fitted, so conversely, they can be removed. https://www.google.com/search?q=B+%26+O+Beosound+3000+glass+doors+will+not+open These are the Bang and Olufsen outlets in London https://stores.bang-olufsen.com/en/united-kingdom/london and finally, there is a repair partner in Eastbourne https://www.av-services.co.uk/bang-olufsen The manual if you need it. It is an elderly system and only does what it does, music and tuner. https://bangolufsenassistentgohe.blob.core.windows.net/manuals/SOUND_SYSTEMS/BEOSOUND_3000/BS3000_RB_EN.pdf . If you need further help, click Comment below. ..

no factory reset --this is user manual page 36 is trouble shooting ----https://www.manualslib.com/products/Radio-Shack-Pro-135-3101070.html

There are a few things you can try to troubleshoot this issue with your 2013 Chrysler 300c's Uconnect Bluetooth system:

1. Make sure that your phone's Bluetooth is turned on and that it is in pairing mode.
2. Check the Uconnect system's settings to ensure that Bluetooth is turned on and that it is set to discoverable mode.
3. Try restarting both the Uconnect system and your phone to see if that resolves the issue.
4. Check the vehicle's manual to see if there are any specific instructions for pairing a device with the Uconnect system.
5. If the above steps don't work, try clearing the Uconnect system's memory of previously paired devices, and then try pairing your phone again.
6. Check if the software of the Uconnect system is up-to-date, if not update the software.
7. Try deleting all previously paired devices on the Uconnect system, and then try pairing your phone.

If none of these steps resolve the issue, it may be a problem with the Uconnect system itself and you may need to take your vehicle to a Chrysler dealership for further assistance.

It appears you can. Normally you load the software to the new PC and then copy the data file to USB and transfer it. It would be a file in USERS. Then reboot the computer. https://www.google.com/search?q=gs3000+scanner+on+one+PC%2C+transfer+that+data+to+a+new+PC ..

Usually because the purchaser didn't read the instructions or because the instructions are badly written from Chinese. This is an eBay special. I wrote this Tip on connecting Bluetooth devices which mentions the step that is always missed. https://www.fixya.com/support/r26362721-pairing_bluetooth_devices

iEssentials Bluetooth FP1 Headset, USB Car Charger ...

https://www.ebay.com > itm iEssentials Bluetooth FP1 Headset, USB Car Charger Included ( IE-HFBLU-FP1 ) · Item Information · Item specifics · Shipping and handling · Sales Tax for an item # ... US$12.95 · ‎In stock

It sounds like you are having an issue with your GP339 radio where the PTT (Push-To-Talk) switch is not transmitting when pressed. Here are a few potential solutions to try:

1. Check the battery: Make sure that the battery is fully charged and properly installed in the radio.
2. Check the antenna: Make sure that the antenna is properly connected and not damaged.
3. Check the settings: Make sure that the radio is set to the correct frequency and that the PTT switch is configured correctly in the settings.
4. Check the microphone: Make sure that the microphone is properly connected and not damaged.
5. Check the programming: Make sure that the radio is properly programmed with the correct settings, including the correct channels and frequencies.
6. Check for physical damage: Make sure that the radio does not have any physical damage, such as a broken switch or damaged wiring.
7. Check that the radio is programmed for the correct channel.
8. Check that the radio is not in "Low Power" mode, if so, switch it to "high power" mode.

If these steps do not resolve the issue, it may be necessary to contact the manufacturer or a professional radio technician for further assistance.

Check the PA circuit. If an aerial was not connected or has a very high SWR, it will cook the output section.

refer to instructions that came with unit, if you lost them google your model number manual. copy and paste https://www.fixya.com/support/t24668314-remove_entire_cutting_head_homelite_hlt ..

Hi, please reach out to your products manfucaturer and ask them to email you the diagram. Thank you.

" of YOUR NTE1197 ". Nope we are Fixya dot com, so you have nothing of ours. Contact them, we are not they. https://www.google.com/search?q=nte+1197 ./.

Question edited for clarity. Question moved from Cars and Trucks to Intercoms. Contact the maker. It is likely that the buzzer sounder has failed, or the power to it. You say you "looked at the wiring diagram", I couldn't find one. I guess you meant the 'circuit board'. https://www.fermax.com/uk/technical-support ..

If the PPT (Push-To-Talk) button on your Rino 650 is not working, there are a few things you can try to troubleshoot the issue:

1. Check the battery: Make sure that the battery is fully charged and properly installed in the device.
2. Check the settings: Make sure that the device is set to the correct frequency and that the PTT button is configured correctly in the settings.
3. Check the physical button: Make sure that the PTT button is not stuck or damaged in any way.
4. Check for software updates: Make sure that your device has the latest software updates installed.
5. Check for interference: Make sure that your device is not too close to other electronic devices that may be causing interference.
6. Check the programming: Make sure that the device is properly programmed with the correct settings, including the correct channels and frequencies.
7. Check if the device is in a low power mode, if so, switch it to high power mode.

If none of the above steps resolve the issue, you may need to contact the manufacturer or a professional technician for further assistance. It's recommended to check the user manual of your device before trying any of the above steps, as the process of troubleshooting a PTT button can vary depending on the model and manufacturer.

As a licenced HAM Radio opperator, you will be aware of the legalities and the frequencies you are allowed to use. What is your question I wonder . ..........................................

If your FT-747GX is not transmitting when you press the PTT button, there are a few things you can try to troubleshoot the issue:

1. Check the settings: Make sure that the transmitter is set to the correct frequency, mode, and power level. Also, check that the mic gain and RF power settings are adjusted correctly.
2. Check the antenna connection: Make sure that the antenna is properly connected to the radio and that there are no loose connections.
3. Check the power supply: Make sure that the radio is receiving adequate power and that the power supply is functioning properly.
4. Check for software updates: Make sure that your device has the latest software updates installed.
5. Check for interference: Make sure that your device is not too close to other electronic devices that may be causing interference.
6. Check the values of the voltage on the main board, as you mentioned, the values of 4.5 and 0 for RX and 0 and 1.4 on TX, it could be possible that one of them is too low or high, which can cause the issue.
7. Check the PTT switch, and make sure that it is working properly and not stuck.

If none of the above steps resolve the issue, you may need to contact the manufacturer or a professional technician for further assistance. It's recommended to check the user manual of your device before trying any of the above steps, as the process of troubleshooting a transmitter can vary depending on the model and manufacturer.