20 Most Recent
Curtis-Mathis CM32010 TV - Page 4 Questions & Answers
I need the code for a remote control the control is an uei the tv is a curtis matis
Visit this site for more details. Type in the site name "Electro-help" either to Google or Yahoo search box [not in the address bar of your browser], and click search. It is an electronic equipments service help site. All details you want are there. Note the position of hyphen in between words in site name, when you type it in. The site will appear as it is in web; subtitled as Service help to electronic home entertainment equipments.
Pull up older posts. You can get all details.
Site is listed with Google. You can locate it either at the bottom part of first search page, or at the top of second page.Sometimes, one among the advertisements by the side and bottom of each post might help you to get details about the availability of spare parts and other components.
When did tvs go digital
It started this yearYou can watch digital on any tv but you do need digital receiver boxYou can use digital antenna if you don't have cable or satelliteEither way you need that digital boxI know - more money to spend
There isn't an audio out
A couple of ideas. 1st does the TV have an earphone jack or AUX out . If so you can get an adapter to go from this plug to your line in on your reciever(if using the earphone jack set the volume low and adjust it up to a suitable level. Too much input from earphone jack could damage system). 2nd if you have a satelight or cable box it may be possible to hook a sound sysyem through these devices instead of the TV. If not using these devices you could get a digital TV conversion box on a whether you need it or not basis and run line out on some of these also.
I do not have a
Try just turning the volume down on the TV. The audio power to the red/white output jacks should be the same at any TV volume since it is expecting you to control the volume with an audio receiver or other amplifier.
Good luck.
Please rate me
Mark
How do i switch from
Hello there,
I really need to know the brand and model number of your universal remote to give the correct instructions. It's also depends on whether or not the universal remote will operate all functions of your TV.
The original Curtis Mathes TV had an INPUT button for switching from TV to AV mode. You should look for a similar button labelled INPUT or SOURCE on the universal remote. If you have one of these buttons, try pressing it repeatedly and see if the TV switches to AV mode. It is easier if you have the AV device (DVD / VCR, etc) switched on and playing while you do this.
If you don't have either of these buttons on your universal remote or you have one and it doesn't switch to AV mode, please let me know the brand and model number of your universal remote. I will then be able to give a more specific answer. Please reply to me by clicking on "Add a Comment" below your question.
Hope this helps.
Regards,
BElectric
My TV has a black
Usually when this happens its caused by CC closed captioning
Check your CC settings and disable
A friend gave us a
GO TO YOUR MENU ON THE TV BY USING YOUR REMOTE AND RESET THE SOUND SECTION TO OTHER THEN SS OR SURROUND SOUND.
I need a remote control
Hi walmarb, my name is John. Welcome to FixYa. You can pick-up a Dollar Store, or Wal-Mart. For $6.00. Thanks for choosing FixYa...John
Trying to hook up to
Check ur tv converter box a small button on the back of the converter box make sure it is not set to channel 4,make sure it set it to channel 3.Put ur tv on channel 3.Take the antena signal input put it in the converter box hole that call ANT.Take the wire that came with the converter box put the wire one side of it connected to the other hole into the converter that said OutPut.The other side of the wire should be connected to the hole in the tv said ANT hole.Now make sure ur tv converter box power a/c cord plug into the a/c power outlet and the power button is press on and have power to the converter box.The converter box now power LED light on indication should be on and it is green.Now the tv CRT screen picture should have a menu of the converter box funsctions.Just follow the on screen instructions and press the enter button on the remote and it will now auto scan for those free air Digital DTV channels.When the auto scan it reaches 100% is it done.Now u have done it.
Picture is half of the
Their is a leaky capacitors in the vertical section of your tv. example of vertical ic LA7837 try to replace the capacitors beside it.
Not finding what you are looking for?