Top 20
Seiko Smart Label 240 Thermal Printer Questions & Answers
What in the world!! I have the Smart Label Printer 450, it is not advancing the label, and the power button is flashing. It will not print a label at all at this point, and when it will end up printi
Unfortunately, this is usually an indication that the label roll in the printer are too old. This action is by design, compatible labels should have a black rectangle on the reverse side and the Smart Label printer uses the black rectangle to orient the label. This means your Smart Label doesn't think its wasting labels, it's just trying to run through what it considers to be unsuitable labels as fast as it can. If you're only printing one label at a time you can recover some labels by correctly the label's line up after each label you print but there's nothing you can do so that your printer will properly advance its current labels.
Remove the current roll, open a new boxed label roll, remove a sealed roll, cut open the sealed plastic, remove fresh label roll and load it in your Label Printer. Power the label printer back on and press the label advance button, it should correctly line up.
Slp 200 windows 7
Seiko has really downgraded its legacy product support and it has minimized its application and driver software available for download. To find software for your SLP 200 you'll have to good to a third party site like Drivers Guide. The link below is for version 7.0.3
Seiko SLP 420 Free Driver Download
Important tips when finding and downloading application/ driver software from non-OEM sites
1. Never install any application from a non-OEM site that says it will scan your computer to determine what files you need. - search using the manufacturer name, model number, and current operating system on the computer you want to install the device on.
2. Only install the files you found. Never download any software suggested.
3. When installing the downloaded files, always select Custom Installation to make sure you only install the software you need. In this case only the application and driver files, nothing else ( no driver updating, security scanning, toolbar, etc. programs).
In the specific case of the Seiko Smart Label printer make sure your printer is not hooked up until the Seiko software tells you to.
Smart Label Printer
If the answers above don't work check your AC adapter with a multimeter to confirm its output voltage. If the voltage is off by more than 1 volt you will need to replace your network driver
Louding lables
You shouldn't have to open the back of the printer. You may be having problems with the platen being too tight to allow you to load labels.
If included a picture to help describe the loading process:
Pulling the lever forward (3) releases the Platen tension. Feeding the labels from the bottom of the roll (4) into the slot shown. With the tension off the Platen you should be able to insert the label all the way through the printer
Down load software smart label 200
The official Seiko site is:
Software Driver Downloads
However, Seiko has deleted its legacy printer support so you will have to find your drivers on a third party site. I've included links to your drivers below:
Seiko SLP 420 Free Driver Download
SIISLP200 Drivers Download for Windows 7 8 XP Vista
Note: With Seiko Smart Label printers make sure your printer is not connected to your computer until the Seiko software tells you to.
Important tips when finding and downloading application/ driver software from non-OEM sites
1. Never install any application from a non-OEM site that says it will scan your computer to determine what files you need. - search using the manufacturer name, model number, and current operating system on the computer you want to install the device on.
2. Only install the files you found. Never download any software suggested.
3. When installing the downloaded files, always select Custom Installation to make sure you only install the software you need. In this case only the application and driver files, nothing else ( no driver updating, security scanning, toolbar, etc. programs).
When I reboot my pc, I get a port monitor error on
1. check the USB cable to see if it is connected properly
2. check to see if you have the device showing the "device manager" if not then reload the device by shutting down the PC.
Then rebooting and connecting the device again to the appropriate port.
Check to see if the device bubble on screen says "new hardware" detected.
If so then your device was enable and is not ready to use.
If not then the device needs a driver update and this can be done by going back to the "device manager" and right clicking to go to "properties" to enable new updated drivers
You may also have to go to the manufacturers site to see if there are any updated drivers available.
How I cured my Seiko ER 9000
This is what I did to "cure" my ER 9000 from locking up etc.
First remove the batteries. Wrap the ER 9000 in four or five layers of cling film ensuring that it is completely sealed. Place it in the freezer overnight. When you remove it the next day, DO NOT remove the cling film until the whole thing comes up to room temperature again otherwise the ER 9000 will get wet from condensation. This should take 2 or 3 hours to be certain. Now remove the cling film and wipe the unit to ensure that it is dry. Refit the batteries ( new ones if you can) then and this is important PRESS RESET before you do anything else. If all is well it should come back to normal. I hope that this is helpful and you have the same success as I had.
If this is successful please give feedback, Thanks
I have a 3 month old hand held battery dictionary that has stopped working.
I have an Seiko ER 9000 which has had reset problems when changing batteries on two separate occasions, this caused keys not to work also lockups, pressing the reset button did not clear the "fault". After removing and replacing the batteries several times and then leaving it for a day or two the problem cleared by itself and then worked perfectly. This as I said happened twice when changing batteries. I can only think that this a logic circuit getting Jammed up. I'm afraid that time and patience is the only cure. I hope this helps
LCD problem, Oxford electronic dictionary
You are wrong there, the health insurance quoting software does not take medical history into account while calculating the subsidies. That is the beauty of Obamacare, health insurance for everyone at the same premiums.
Not finding what you are looking for?