Element Electronics ELCHW261 26 in. TV - Page 8 - Answered Questions & Fixed issues

www.elementelectronics.com/support

http://freschematics.sd.bu.eg.com/ Try this link. It has schematics to more than 30,000 devics for free download.

If you wish to get more details; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. Common codes to check devices with different brand TVs are given, in the order of the device's brand name list in alphabetical order. Pull up older posts. Surf the site with patience. http://remotesearch.blogspot.com/ http://electrohelponline.blogspot.com/

Fault with main board. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/

Make sure that the channel you are trying to view is in the package that you have through the cable services.

this might help http://www.elementelectronics.com/wp-content/uploads/2013/06/ELCFW329-User-Manual.pdf

Either wired incorrectly or is a settings issue.

If you wish to get more details; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. Common codes to check devices with different brand TVs are given, in the order of the device's brand name list in alphabetical order. Pull up older posts. Surf the site with patience. http://remotesearch.blogspot.com/ http://electrohelponline.blogspot.com/

Contact any service technician. Gopakumar Gopalan Google

There should be a "master" reset button hidden on the unit somewhere. It is likely behind a very small hole that you could push a straightened out paper clip into. If you find the hole, turn the TV on and then push the button in until the TV turns off. When it restarts it should allow you to program the TV.

Sometimes this kind of behavior indicates that the TV needs to be reset. Unplugging it overnight should cause a reset. Often the underlying problem returns, however. Good luck!

Back-light fault. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. Do a search by type in the brand name of your device at its search box. It will be best to replace the inverter board as card basis. http://electronicshelponline.blogspot.com/

These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. Viewing it in "Mosaic" or "Magazine" will make surf easy. http://electronicshelponline.blogspot.com/ Blinking codes details to many popular brand TVs are given. Surf the site with patience. Do a search by type in the brand name of the device to the search box.

Source button is to use to select the input sourse; ie, TV / AV / HDMI / SCART. Electro help

Sounds like the tuner fault. Contact any service technician. If you wish to get some details; check the site linked here. Viewing it in "Mosaic" or "Magazine" will make surf easy. Pull up older posts. Surf the site with patience. Do a search by type in the brand name of your device at its search box and press "Enter". http://electronicshelponline.blogspot.com/

You'll need a subscription to Direct TV at the least. But the new box may also assume a digital ready TV, and if you don't have one that would be the issue.

use google to find your specific model of element tv. you should be able to determine what inputs your set has. find a compatible input for the devices you wish to connect and connect them to the inputs utilizing the cables needed. once this is done, turn your tv on, set it to the input desired, turn on the device and enjoy

I'm not clear on what you are having trouble with. From looking up the Cameron cable selection list, if you have their 'Full Basic" service , you should be receiving 88 channels. or 93 channels, depending on where you live. And possibly where you live, Cameron has a different package from the ones I mentioned. If you are having trouble with the signal or you are receiving all the channels in your package, you should contact your cable company. Or possibly you are looking for channels that are not included in your package???

Start here... http://www.searshomeservices.com/element-television-repair Or here: http://www.yellowpages.com/60638/tv-repair Or here: http://www.elementelectronics.com/support/

Try disconnecting the unit completely from power source for 10 minutes. Reconnect unit and try.