20 Most Recent Element Electronics ELCHW261 26 in. TV - Page 7 Questions & Answers


Codes are stored in the remote.

Element... | Answered on Dec 15, 2015


If you wish to buy its original remote control, contact the authorized service centre, or authorized dealer to your device brand. They can either give you a genuine remote control to your device, or can direct you, from where can you purchase a suitable one.
To select a proper universal remote control, you should know about the number of digits to its set-up codes. There are 3 digit, 4 digit, 5 digit, 2 digit and even single digit codes, to some brand devices. After confirming this, check the sites linked here. Both the sites have set-up code list and set-up procedure to many popular brand remote controls. Check which brand remote control has set-up code/s to your device brand, and buy that one according to availability. Brand name of the remote control isn't a matter, but it should have set-up codes in its code list, to the device brand you have.
Please note: Every new universal remote control will have set-up code list, and set-up procedure along with its pack. Never accept a remote control, that hasn't both of this. For more details about the set-up codes, visit the sites Check this site too.
http://remotesearch.blogspot.com/
http://electrohelponline.blogspot.com/
Universal remote controls are available at most of the electronic spare part selling shops. Visit some online sites too, which deals with electronic spare parts.

Element... | Answered on Dec 10, 2015


Fault to the main power supply regulator section. Start voltage section circuit fault. Either it will be a separate board, or the part of main board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts.
http://electronicshelponline.blogspot.com/
It will be best to replace the power supply regulator board as card basis rather than making "Surgery" to it; which usually will make loss for both money and time. Even though you can make it right, it will cost around an amount equal to the cost of a new board; including the cost of (spare parts + service charge) More to say, most of the spare parts to it will be difficult to get from open electronic spare part market. This is true to most of the flat panel TV power supply boards; irrespective of its brand and screen size.

Element... | Answered on Dec 07, 2015


0183,0120. Try these codes. If you wish to get more details; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. Common set-up codes to check with TVs and other devices are given, in the order of the "device's brand name list" in alphabetical order. Pull up older posts.
http://electronicshelponline.blogspot.com/
http://electro-medical.blogspot.com/
http://remotesearch.blogspot.com/
http://electrohelponline.blogspot.com/
Search the site by type in the brand name to your device, in the "Search box at the top right of the display window" to see the set-up codes to your device, with different brand remote controls.

Element... | Answered on Nov 28, 2015


Main system control memory IC fault. Check and replace it. Contact any service technician. If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/

Element... | Answered on Nov 12, 2015


Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis.
http://electronicshelponline.blogspot.com/
To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement.

Element... | Answered on Nov 09, 2015


hi,
To understand how to connect the nintendo wii to your tv check the video.
http://electro-medical.blogspot.com/

How To Connect The Nintendo Wii to HDTV 1080p HD

Element... | Answered on Nov 08, 2015


Surf the site with patience. http://electronicshelponline.blogspot.com/
Circuit diagrams of many popular brand devices are given. Search the site by type in the "brand name" to your device, in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.

Element... | Answered on Oct 19, 2015


Main system control memory IC fault. Replace it. If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/

Element... | Answered on Oct 13, 2015


ensure the set is adjusted to receive the type of channels that are broadcast in your area. By this I mean that if digital is broadcast ensure the tv is setup for digital reception.
I assume that you are using an antenna/aerial. Ensure that this correctly installed and is functioning, there may be a facility on the tv to check the reception via a swr meter of some kind, basically a utiliity that registers that an aerial is bringing in some kind of signal.
It cannot be anything else, if the tv is setup for the local broadcast type and the aerial is connected the signals should be found unless you have very bad reception due to environmental conditions.... in which case you may have to invest in a reception booster/signal amplifier.

Element... | Answered on Oct 13, 2015


look on the screen sides or under the tv there should be a power button. push that once to turn the tv on and off

Element... | Answered on Oct 12, 2015


Most LCD TVs that are three years old or older that have the "sound but no picture issue" have experienced a failure of the LCD backlight circuit. Older units were fluorescent bulbs that used an inverter (ballast) to produce the light that shines through the LCD and allows you to see the image. These inverters fail after 3-5 years of use.

Element... | Answered on Oct 03, 2015


DIRECTV- 10178
Time Warner Cable- 10178
Comcast- 10178
Cox Communications- 10178
Dish Network- 627 or 659

This is from the remote control guide that came in my box for model elefw408 hope this helps

Element... | Answered on Sep 03, 2015


Sounds like main board fault. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/ . In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.

Element... | Answered on Aug 27, 2015


Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis.
http://electronicshelponline.blogspot.com/
Some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement.

Element... | Answered on Aug 04, 2015


0421 0435 0469 0611 0159
Try these codes. If you wish to get more details; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. Common set-up codes to check with TVs and other devices are given, in the order of the "device's brand name list" in alphabetical order. Pull up older posts.
http://electronicshelponline.blogspot.com/
http://electro-medical.blogspot.com/
http://remotesearch.blogspot.com/
http://electrohelponline.blogspot.com/
Search the site by type in the brand name to your device, in the "Search box at the top right of the display window" to see the set-up codes to your device, with different brand remote controls. Three digit, four digit and five digit code list to different remote controls are given.

Element... | Answered on Aug 02, 2015

Not finding what you are looking for?
Element Electronics ELCHW261 26 in. TV Logo

70 questions posted

Ask a Question

Usually answered in minutes!

Top Element Electronics Televison & Video Experts

Cindy Wells

Level 3 Expert

6000 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

LP

Level 3 Expert

514 Answers

Are you an Element Electronics Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Element Electronics Televison & Video

  • Element Electronics Televison & Video

Most Popular Question

element elchs261 wont turn not even red

  • Televison & Video
Loading...