Top 20
Philips GoGear ViBE Digital Media Player Questions & Answers
How do you store podcasts best on a phillips mp4 vibe?
If the device offers the ability to create folders (like rock, folk, classical) that are selectable, create one called podcasts. If not, retitle all the podcasts so that the file names all start with a Z, and then at least they will be at the bottom of a master list when played in sequence. Doesn't help in shuffle mode though, as the podcasts will still play randomly if you can't isolate them to a separate folder.
Error code f0305023
my philips GoGear Vibe when i start file system error
error code F0305023 what i do now?
how can start this? pl. help me.
Error code 3
A Apple iPod a1236 is locked and I have no code to unlock it. What do I do?
Not registering on computer
Hi carebear_nobTry this solution to your problem.Go to Device ManagerTo get to Device Manager you will:Right click on My Computer>Properties>click the Hardware Tab>Device Manager.After you are in Device Manager look for your MP3 player or Unit.Here you should see no "Yellow" exclamation points.If you do they they are telling you that you have a device conflict.If you currently have your unit plugged in, you may notice the "unknown device" which would be your Player or Unit.If you unit has an exclamation point by it, then you will need to click on it and delete it.After you remove all devices with conflicts then click on refresh and search again for your MP3 player/Device.The computer should install your device this time and solve your problem with connection of the MP3 player/Device.Please take time to rate me.Bud
Computer will not recognize the device when connected
Hi mike wesselsTry this solution to your problem.Go to Device ManagerTo get to Device Manager you will:Right click on My Computer>Properties>click the Hardware Tab>Device Manager.After you are in Device Manager look for your MP3 player or Unit.Here you should see no "Yellow" exclamation points.If you do they they are telling you that you have a device conflict.If you currently have your unit plugged in, you may notice the "unknown device" which would be your Player or Unit.If you unit has an exclamation point by it, then you will need to click on it and delete it.After you remove all devices with conflicts then click on refresh and search again for your MP3 player/Device.The computer should install your device this time and solve your problem with connection of the MP3 player/Device.Please take time to rate meBud
FM radio
The FM Radio on your mp3 lets you listen to the radio (only FM stations)
I lost my insallation disk
Go to Philips web site. Click on support, then software & drivers. You will find a newer driver there than your instalation disc!
My volume button broke
1 Reset your GoGear with something sharp like the tip of a pen or the end of a paper clip, if you're device isn't working properly or there's a frozen display. Insert the sharp object into the "Reset" hole (located at the bottom of the player), and hold it there until the device turns off. If resetting the device does nothing to restore the display, access the "Philips Device Manager" through your computer to recover the GoGear.2 Click "Start" on your computer, then "Programs," "Philips Digital Audio Player," "Aria Device Manager," and then "Philips Device Manager." This will launch the "Philips Device Manager." Make sure the GoGear is turned off completely. Connect your GoGear to your computer while holding down the "Volume Up" button. Continue to hold the "Volume Up" button on your GoGear, until the "Philips Device Manager" recognizes the device and enters recovery mode. Click the "Repair" button when it appears on your computer, then follow the steps to fully recover the GoGear. Properly disconnect your GoGear from your computer and restart the device.3 Recharge your device if your GoGear dies suddenly while playing. Connect the GoGear to your computer via the supplied USB cord. Plug one end of the USB cord into a functional, open USB port on your computer. Plug the free, smaller end of the USB cord firmly into the small USB jack on your GoGear and turn your computer on. This will begin the charging process of your GoGear. If recharging doesn't work, the battery may need to be replaced. Check that your GoGear isn't in standby mode. Hold the "Power" button for two seconds to turn it back on.
Not finding what you are looking for?