Kenmore 16372 / 16374 / 16379 Built-in Dishwasher - Answered Questions & Fixed issues

Sounds like your main wash motor is bad or locked up. If you need further help, reach me via phone at https://www.6ya.com/expert/ronald_e6b9572cebe3ad27

The full water level will be 1/4 to 1/8 inch below the heating element. The water fills on a timed basis so the exact level depends on incoming water pressure.

Sounds like water-level sensor is ok as it stops filling then 'hums'. I'd (carefully) check the connections to the connections between the level-sensor and the wash motor start relay. Could be motor is bad or something is causing it to become 'jammed'. Before you begin opening the appliance, I'd attempt to vacuum out the water or try putting the control in the last position to cause it to try to pump out the water.

Hi,

The scum, film and white residue problems have started since the reduction of phosphates in dishwasher detergents.

Here is a tip that will help you to solve the problem of films, residue, and scum in your dishwasher.

Dishwasher Residue and Film on Dishes

heatman101

//

Hi,

I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms online and installed them in minutes...now the thing works like new... However I have also found that if the heating element goes bad then that also can mess things up bad... So I would buy new spray arms, and also check out the heating element to make sure it is working... Here is a tip that will help you with the online buying...

Dishwasher Spray Arms not Spinning

How to Buy Appliance Parts Online

A bad heating element causes many problems in dishwashers...

Dishwasher Problems The Heating Element not Working

Dishwasher Maintenance

heatman101

Asker's Testimonial "explanation very clear. will give it a go and see how simple it was. thanks Ronnie " - ronnieshomes
..................................

Hi

Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doesn't allow the door to open. The strip may not be getting 120V or maybe disconnected. Kenmore dishwashers use a wax motor to open the soap dispenser. The plunger inside the wax motor slowly moves and pushes the plunger and door open.

And, if this wax motor doesn't receive 120 volts, then it'll not work. Please check the voltage to the wax motor/Bi-metal strip; also inspect the connections to these. Hope this helps... Please post back if you need more information.

Daniel

Hi,

I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms online and installed them in minutes...now the thing works like new... However I have also found that if the heating element goes bad then that also can mess things up bad... So I would buy new spray arms, and also check out the heating element to make sure it is working... Here is a tip that will help you with the online buying... Dishwasher Spray Arms not SpinningHow to Buy Appliance Parts OnlineA bad heating element causes many problems in dishwashers...Dishwasher Problems The Heating Element not WorkingDishwasher Maintenanceheatman101 68a,ls

Hi,

That is not that hard to fix and you can easily buy the parts yourself online...

Here is a tip that will help you with the online buying...

How to Buy Appliance Parts Online

heatman101

Hi,
Check your heating element..

A bad heating element causes many problems in dishwashers…

Dishwasher Problems The Heating Element not Working

Dishwasher Maintenance

heatman101

Asker's Testimonial " explanation very clear. will give it a go and see how simple it was. thanks Ronnie " - ronnieshomes

Hi,

This is caused by water not heating properly. I have put together some instructions on what to check and how to reset the control so you can use the dishwasher again. Follow the link below and let me know if it works out for you.

http://www.fixya.com/support/r4628906-flashing_or_blinking_green_clean_light_7

Water level can depend on the model and manufacturer. The water will fill to the level of the float switch. This is a plastic looking thing near the front of the dishwasher along the tub bottom that looks like and upside down cup. The water level reaches a point to where the float lifts and activates a cut-off switch which will stop the water from filling, followed by the wash cycle beginning. Now, depending on where the heating element is located, the water level is usually just touching the element and not necessarilty covering it. Does this help you? If you still have questions, let me know.

usuall the model and serial plate is l;ocate d al;og the top of inner door panel or the inside of teh inner rim of tub itself

so here it is...
get a screw driver (you may need a "star" head driver as well), get in there and take out all that you can and clean it (it all comes out pretty easily)...you will find a lot of undisolved soap and hard water build up...rinse it, scrape it, vacuum it...just get out as much as you can...keep note of how you took it apart so you can put it back together...then put 1/2 to a whole gallon of vinegar in and run a cycle (hi-temp if you have that option)...if it was like mine most of your sprayers were gummed up and the water just wasn't moving through the machine...

to avoid this problem...use half of what you have been using of your detergent...and only fill the "pre rinse" section if you are doing pots and pans....and then only fill that half way as well.
after that run a few cups of vinegar through on an empty cycle once a month...
whole job (not including the wash cycle) 1.5 hours...

Sorry to take so long getting back to you. Go to searspartsdirect.com and type your complete model number in the "Search by Model Number" window. Follow the links on the next page. You can also try repairclinic.com. The website offer competitive pricing with one of the other usually having the better price. The Sears website offers helpful parts diagrams. If you have any futher questions, please let me know.

NOTE: There may be a possibilty that you could have damaged the part you already replaced. It is recommended that you replace BOTH components at the same time. They are available as a SET on both websites I believe.

NOTE: Make sure your exhause ducting is clear as well before starting the unit or it will overheat and do the same thing.

Problem was that a rat or mouse chewed through the hose. I had seen small pieces of red plastic on the floor in the water. That was a clue that the plastic part of the hose had been chewed up.

You can try
www.appliancepartspros.com/
appliancehelp.com
http://www.partselect.com.

These sites also include how to guides that ship in along with the parts so it would just be a piece of cake!

Good luck!
Sai.

Yes you can surely do it yourself..its just unplugging a few wires remove the old one and just install the new one..
I couldn't find the model number you have specified, but you can give these guys a call and specify ask for a new touchpad for kenmore 16372. They will ship it out for you.. I advise you call their toll free number that you can find on their site so that you can get it done real quick.. http://www.laundryparts.com/sunshop/index.php?action=category&id=bestsellers

you can find it on Appliance Parts.com, Appliance Pros.com Discount Appliance Parts and Appliance Repair Parts.
The model you included isn't actually the model number. The data tag is somewhere near the door gasket, so include that for sure so that i can directly guide you to the purchase zone..

It is the touchpad that is faulty.. coz if the control board is faulty the unit may not respond to any button at all.. So just get a new touch pad.. If you want to buy it online.. then let me knnow i will get you the link..

Question edited for clarity. Manual https://www.manualslib.com/products/Kenmore-665-Prefix-257208.html More here https://www.google.com/search?q=kenmore+Dishwasher+model+665+1678582+manual ..