20 Most Recent
Yamaha Rx-v465/rxv465 Home Theater Receiver - Page 4 Questions & Answers
Any idea what firmware the yamaha RXV465 is
CHECK UPDATED VERSION Press and hold the [STRAIGHT] button on the front panel and keep it pressed while you press the [STANDBY/ON] button. Once the front panel displays "Advance Setup", release the [STRAIGHT] button. Then, press and hold the [TONE CONTROL] button for about 3 seconds until front panel displays “M:K032 8FFD”.
K032: version of firmware 8FFD: checksum
3/10/2010 10:26:18 PM •
Yamaha...
•
Answered
on Mar 10, 2010
Is a yamaha rx-v465 supposed to recieved both
What connection do you use?
This receiver supports both video and audio over HDMI. It has also other video inputs, but it doesn't have any video processing.
So if you connect your equipment for example to component video in, its video output will be present only on component video out (NOT on the HDMI output nor s-video output).
3/3/2010 7:11:17 AM •
Yamaha...
•
Answered
on Mar 03, 2010
I get no bass sound from sub-Woofer connected to Yamaha RX-V465
Check your speaker settings in Setup menu / Speaker Setup / Manual / Config (and then in this submenu also Equalizer).
In Config, choose where should low frequency sound go - subwoofer and/or front speakers (if they are big enough). The settings are: Bass Out: SWFR/Front/Both.
Also check Subwoofer phrase in SWFR Phase.
Check settings of all speakers, they can be Large / Small / None. If small, frequencies lower than "Crossover" settings, will not be put on them.
3/2/2010 3:53:21 PM •
Yamaha...
•
Answered
on Mar 02, 2010
RX-V465 output HDMI 1 will work but HDMI 2-4 won't
This receiver has only one HDMI output, but 4 HDMI inputs. If some inputs don't work, try connecting the equipment (DVD for example) to HDMI input which works with other equipment....
For the RCA (composite) video input - it won't work, because this receiver don't have any video processing circuit.
So HDMI input video goes to HDMI outout connector.
Composite (RCA) video input goes to Composite outout and no other video output.
S-video input goes only to s-video output.
3/2/2010 3:43:54 PM •
Yamaha...
•
Answered
on Mar 02, 2010
Hdmi connection from receiver to hdtv, with set
Check your HDMI sound settings. You can choose it HDMI sound should go to receiver+speakers or to TV.
It is in menu: Setup / Func. setup / HDMI Audio. Options are: Amp / TV / Amp+TV.
3/2/2010 3:40:53 PM •
Yamaha...
•
Answered
on Mar 02, 2010
I have yamaha rx-v465 receiver and yds-11 docking
I think it is not possible, because RX-V465 does not have HDMI-video processing. It can only pass-thru the HDMI video to HDMI-out, but not alter the signal in any way.
If it should support TV output with YDS-11, it will work only via analog video out (s-video / composite / component).
3/2/2010 3:34:52 PM •
Yamaha...
•
Answered
on Mar 02, 2010
How do u know if the decoder for dd and dts is
When listening to digital source (HDMI or spdif optical/coax), press Option button on remote and choose Signal Info submenu. There you can see info about number of channels, bitrate and decoder which is currently used.
3/2/2010 3:32:47 PM •
Yamaha...
•
Answered
on Mar 02, 2010
Haveing trouble syncing the sound with lips is
RX-V465 has auto-sync feature over HDMI. So if you have your DVD and TV connected over HDMI, receiver will communicate with your TV and set the delay automatically based on TV processing speed.
You can turn auto-sync on in Setup menu / Sound Setup / Lipsync / HDMI Auto.
Or if that doesn't work for you, you can set a value in milliseconds manually in the same submenu.
3/2/2010 3:30:03 PM •
Yamaha...
•
Answered
on Mar 02, 2010
How to install RX-V465
Hooking up the stereo to the speakers is straight forward. 2 wires each speaker. a positive and negative they go to the corresponding speaker input. As far as hooking up the tv it all depends on what kind of video connection you are using. Most likely you plug all your devices into the reciever then go from the monitor out on the receiver to the tv.
This link may help you.
http://www.howtohookitup.com/surround_sound.htmlIf you need further assistance please let me know.
Thank you,
Lee
11/12/2009 5:36:24 AM •
Yamaha...
•
Answered
on Nov 12, 2009
I recently bought a RX-V465 receiver and I need to
1 - As you already have it, take it out of the box and look at the back. You should be able to determine the connections from there. It is also in the owners manual.
2 - The receiver only supports 6 and 8 ohm speakers. Do not use 3 ohm speakers with it.
3 - The Yamaha website has instructions on how to check the firmware version and instruction on how to upgrade the firmware.
11/6/2009 1:04:01 PM •
Yamaha...
•
Answered
on Nov 06, 2009
Let me be more specific on our problem. We
Look towards the back of the manual. You go into setup. Choose HDMI. Then there is another setting that you have to activate. The receiver must be set to the HDMI input that you want, before the receiver is turned off. I just installed my receiver last night and followed that procedure. Works great.
11/6/2009 12:57:00 PM •
Yamaha...
•
Answered
on Nov 06, 2009
Not finding what you are looking for?