Top 20 VXI Corporation Blueparrott B250-XT Bluetooth Headset Questions & Answers

It is actually very easy to remove the battery on the BlueParrott B250-XT. To remove the earpiece, just pull it out of the socket but be careful not to pull the wire attached to it when you separate it from the body. Next, remove the five screws to access the battery compartment. Disconnect the battery from the board and leave it disconnected for 10 minutes or so. Re-connect the battery and re-assemble. Connect the headset to your charger and after a couple of minutes, it should start charging showing red until fully charged. If it still won't charge, you may have to order a new battery. You can find a replacement battery on EBAY for around 10 dollars. Repeat the battery replacement and check to see if it starts to charge. If it works, you are good to go. If it does no work, you may have to send it to the manufacturer for repair. Good Luck!

be sure you have your media volume turned up. You can also call VXI they offet excellent tech support

www.vxicorp.com/customer-care/technical-support

You go here and contact them. http://www.vxicorp.com/customer-care/service-and-repair/

This is a new Bluetooth Parrot B250-XT

Eileen, There are 2 parts to bluetooth. Step 1 is pairing. You need to set the phone AND the headset to detect each other (pairing mode). The phone is the easy part - it will tell you on the screen that it is searching for the headset. The headset has a specific way to put it in detect/pair mode. Sometimes it is holding down the power button for 5 seconds or longer. When the phone detects the headset, it will ask for the password and allow you to name it. Sometimes, the phones already try the default 0000 passcodes and connect automatically. Step 2 is connecting to the bluetooth device. If you are connected and can make and receive calls, you don't need to do anything anymore. Best of luck.

Eileen, There are 2 parts to bluetooth. step 1 is pairing. You need to set the phone AND the headset to detect each other (pairing mode). The phone is the easy part - it will tell you on the screen that it is searching for the headset. The headset has a specific way to put it in detect/pair mode. Sometimes it is holding down the power button for 5 seconds or longer. When the phone detects the headset, it will ask for the password and allow you to name it. Sometimes, the phones already try the default 0000 passcodes and connect automatically. Step 2 is connecting to the bluetooth device. If you are connected and can make and receive calls, you don't need to do anything anymore. Best of luck.

Please be more specific.

While device is on hold both volume buttons for 6 seconds till you hear 2 tones. Then plug in factory supplied charger for 10 seconds. Unplug a d re-pair to your device

just bought a iphone, an the sound on the other end is lousy

INCREASE VOLUME

9vdc positive tip. Road King RPDC-812 available at most truck stops work great it's a universal dc adapter and the orange end fits the 250xt. Price $15 at Love's.

Assuming you are talking about the B250-XT headset, you need a new battery. They are found at http://www.commstactical.com/Extended-Life-Battery-for-Bluetooth-Headsets-BP002.htm

Delete the old pairing and do it again. Also try to pair with another BT device (if possible) to see if the problem is the headset or not.

configuration made bad

the default pass key for all phones or headsets is usually 0000 that's 4 zero's.

I don' think the B250-XT was designed with lisening to music in mind. There is a new mondel out now that can be found at Pilot Truck Stops that is called the B250-XT Plus that will provide that function.

blue parrot will not connect to iphone

check if the cable is properly plug in. wait for until 5 minutes and see if it's charging. if it's still not charging, it needs a repair. kindly rate this post and thank you for choosing fixya.