Top 20
Kenmore 23822 Top Load Washer Questions & Answers
My washing machine was tripping circuit breaker. I
Hi, I think the trip going is an electrical fault, DO NOT BYPASS IT, but, with power OFF AND UNPLUGED, meter both power wires to earth, (chassies) you should not get any readings. If it happens at the same point in cycle, that might narrow down the fault, i.e, every time the machiene pump emptys, its the pump/wire to it. Any doubt, get it sorted by a reliable tech guy, and good luck finding one of those!!
HOW DO YU GET THE SPNNER NUT KENMORE 90 SERIES WASHER?
You'll really will need the spanner wrench for the spanner nut on the basket drive block. If you try to make a tool or use some other method, you risk injury and possibly damaging your washer basket.
The spanner wrench is made by Supco, part #TB123A. It has various other part numbers from the appliance manufacturers. It is compatible with Whirlpool, Maytag, GE, and Kenmore. Most Kenmores are made by Whirlpool.
If you want the wrench same day, call local appliance shops and ask if they sell the spanner for the Kenmore Series 90. I got mine from a local shop and paid $13.
You could also buy one on eBay or another reasonable online source.
http://www.ebay.com/sch/i.html?_trksid=p2050601.m570.l1313&_nkw=tb123a&_sacat=0&_from=R40
Or Google search: TB123A
Don't pay more than $20 including shipping.
You can always sell it on eBay once you are done with it. It won't lose much value being used since it doesn't really wear out.
You'll need a hammer too, preferably with a hard rubber head, or use a wooden mallet. If you use a steel hammer, be careful when you strike the spanner wrench to loosen the spanner nut. Wrap the steel hammer head in an old washcloth or rag. You don't want to accidentally strike the porcelain enamel lining of the basket - it will chip and that can lead to rust of the metal.
Will not agitate or spin water out
The most common cause of this is a defective washer lid safety switch, if the washer doesn't sense the lid is closed nothing will happen other than it will fill with water, no wash cycle or spin. The lid switch is accessed by paying your washer top off with a putty knife, it is held down by friction spring clips, the lid switch is under the top, you will see it. You can obtain a replacement part from Sears Direct for about $15.00 US
Please rate my help for Fixya, it improves my status and it is all I ask for my time helping you with your problem. Thanks
I am getting a F50
Hello,
here is what the F50 error code means and what must be checked when it comes up
F50
(F50)
Motor Stalled
F then 50 flashes when the motor rotor position sensor (RPS) senses no rotation.
Does basket turn freely? If not, make sure bottom shipping pack has been removed. Determine cause of friction.
Kenmore ultra fabric care ll heavy duty 90 series.
If this machine is new or old sometimes wash items get out of the basin and clog up the pump. This may not be the problem in your case. Let's look at the pump. Is the belt tight? Sometimes you can see into the pump ,is there something visible in the pump preventing it from turning? Is the belt worn to the point that can't turn the pump pulley? With belt off pulley ,can the pulley be turned by hand one way or the other, I mean is it seized?Check these suggestions, and get back to me with how you made out. GOOD LUCK.
Fills with water and then
Top load machines will fill with water while the lid is open. Your problem starts when you close your lid. NOTHING happens. I believe this to be your LID SWITCH . Replace or have replaced and you should be OK. GOOD LUCK.
Washer will not spin. water
With old washers and with new washers sometimes you have to get in there and tighten the belt or replace the belt. Your problem sounds like this to me.Your question was posted sometime ago and you probably found your problem. If not please get back to me and I will be happy to help some more. GOOD LUCK.
Roper washer will not aggitate
Open the lid, pop off the softener cup, you will find a gear that moves the agitator. It is made of plastic, or nylon. These gears tend to break sometimes. If it's not under the softener cup then unbolt the bolt under the softener cup, and lift off the agitator. You will find the gear there. This is usually a very simple fix and can be done by anyone at small expense. Please let me know if I have been helpful. GOOD LUCK.
Not finding what you are looking for?