20 Most Recent
Kenmore 23822 Top Load Washer - Page 3 Questions & Answers
Will not agitate or spin water out
The most common cause of this is a defective washer lid safety switch, if the washer doesn't sense the lid is closed nothing will happen other than it will fill with water, no wash cycle or spin. The lid switch is accessed by paying your washer top off with a putty knife, it is held down by friction spring clips, the lid switch is under the top, you will see it. You can obtain a replacement part from Sears Direct for about $15.00 US
Please rate my help for Fixya, it improves my status and it is all I ask for my time helping you with your problem. Thanks
Fills with water and then
Top load machines will fill with water while the lid is open. Your problem starts when you close your lid. NOTHING happens. I believe this to be your LID SWITCH . Replace or have replaced and you should be OK. GOOD LUCK.
Washer will not spin. water
With old washers and with new washers sometimes you have to get in there and tighten the belt or replace the belt. Your problem sounds like this to me.Your question was posted sometime ago and you probably found your problem. If not please get back to me and I will be happy to help some more. GOOD LUCK.
Kenmore ultra fabric care ll heavy duty 90 series.
If this machine is new or old sometimes wash items get out of the basin and clog up the pump. This may not be the problem in your case. Let's look at the pump. Is the belt tight? Sometimes you can see into the pump ,is there something visible in the pump preventing it from turning? Is the belt worn to the point that can't turn the pump pulley? With belt off pulley ,can the pulley be turned by hand one way or the other, I mean is it seized?Check these suggestions, and get back to me with how you made out. GOOD LUCK.
Roper washer will not aggitate
Open the lid, pop off the softener cup, you will find a gear that moves the agitator. It is made of plastic, or nylon. These gears tend to break sometimes. If it's not under the softener cup then unbolt the bolt under the softener cup, and lift off the agitator. You will find the gear there. This is usually a very simple fix and can be done by anyone at small expense. Please let me know if I have been helpful. GOOD LUCK.
I am getting a F50
Hello,
here is what the F50 error code means and what must be checked when it comes up
F50
(F50)
Motor Stalled
F then 50 flashes when the motor rotor position sensor (RPS) senses no rotation.
Does basket turn freely? If not, make sure bottom shipping pack has been removed. Determine cause of friction.
Water is leaking onto floor
you will have to check the hoses coming from the water inlet solinoids as it sounds as if there is a leak in one of them.
Kenmore model # 110.23832100
Washer would
sounds like it's in the re-assembly since the water pump is directly connected to what you just did. take it apart once again and make sure all is put back right and water pump is properly seated on motor shaft.
How can i get an
check the website of the manufacturer and download the manual 4rm there
My Kenmore Series does not
Easy fix no parts needed. Flip up the controls and hunt down the water level switch, looks like this:
See the small tube? If it vibrated off there just re-secure it and pump out the water.
If it looks intact and is connect to the water level switch then yank it off there and blow out the sediment in the base of the tub. Re connect the hose and pump out the water. These water level switches rarely go bad. But sediment gets into a lot of these washers especially if you live near the beach.
Video: how to get into these machines If you need further help, reach me via phone at
https://www.6ya.com/expert/dan_73bbd84fe1d95b61
During the spin cycle I
Hi Brad,
The sound should be coming from drain pump or drain pump filter. Disconnect the hose from the drain filter and drain pump, clean the pump & filter. Check below video for details--
Hope this helps... Please post back if you need more information.
Daniel
The commercial dryer doesn't heat
Hi,
If you are having problems with your gas dryer not heating the most common problem is that the ignitor goes bad. Even though it glows sometimes it is still not working properly.
if you dryer is gas check out this gas no heat tip....
If you have an electric dryer, you can have many different things that can go wrong causing the dryer not to heat.
check out this electric no heat tip...
heatman101
LOAD TOO WET AFTER SPIN CYCLE
- NOT DRAINING PROPERLY
- spin bowl not turning
- spin bowl slipping and not gaining proper speed
- pump blocked
- pump not working
- too much soap used
- take out pump and check all the water ways
- observe the spin bowl turning
- Next call for pro help
Not finding what you are looking for?