20 Most Recent D-Link DIR-615 Wireless Router - Page 9 Questions & Answers

To connectyour computer to a wireless router, you click the Refresh networklist, then Choose your wireless network and then click Connectto your secured Wireless Network, it will asks for a Network Keybefore allowing you to connect into your wireless network. This NetworkKey is either the WEP, or WPA or WPA2 Encryption key that is used toconfigure the Wireless Router. The Passphrase is an alternate way tosetup the Encryption key.When you are requested for a Network Key, you can just enter the Passphrasethat was used to configure the Encryption key in the wireless router.http://www.fixya.com/support/r5270415-network_password_network_addressFor information on securing your wireless network,configuring the wireless router and configuring the wireless card in thelaptop/computer, please click on this link and follow my instructions :-http://www.fixya.com/support/r3559128-wireless_router_security

You need to secure your wireless network with WPA or WPA2 encryption.Connect a LAN cable from the D-Link to your laptop/computer'sLAN port, open the browser on your laptop/computer and enter the D-Link's configurationURL..http://192.168.0.1The default login = adminThe default PW = blank (just press Enter)You can now change the default admin password.You can now configure the wireless settings. Now configure the wireless card in your computer/laptop withthe router's wireless settings.To secure your wireless network from unauthorized access,please click on this link and follow my instructions :-http://www.fixya.com/support/r3559128-wireless_router_security

Try calling your internet provider or go to http://www.dlink.co.uk/cs/Satellite?c=Page&childpagename=DLinkEurope-GB%2FDLTechHome&cid=1197318962147&p=1197318962147&pagename=DLinkEurope-GB%2FDLWrapper

If the default password on the D-Link has been changed then-To reset the D-Link back to the default settings -Press and hold the RESET button at the back of the router with the power ONuntil the LEDs flash at the time the release the RESET button. (firmware version was 3.00, and upgraded to3.05)Connect a LAN cable from the D-Link to your laptop/computer'sLAN port, open the browser on your laptop/computer and enter the D-Link's configurationURL..http://192.168.0.1The default login = adminThe default PW = blank (just press Enter)You can now change the default admin password.You can now configure the wireless settings. Now configure the wireless card in your computer/laptop withthe router's wireless settings.To secure your wireless network from unauthorized access,please click on this link and follow my instructions :-http://www.fixya.com/support/r3559128-wireless_router_security

what is indicated below the blinking lite...if your not getting a signal...try unplugging the units power...wait 4-5 minutes and plug it back in and see if it resets itself....phillip

Sticker on the underside usually. Try connecting via ethernet and going to 192.168.1.1 in your browser.

ello, please do this to get your Passkey or Change it.

1) Open your Internet browser and go to http://192.168.0.1/.

2) When prompted use admin as the username and leave the password XXXXX (if that doesn't work use admin as the password).

3) Once logged in, click the Wireless button on the left.

4) Look for the Security Mode choice and see which choice is clicked.

5) If WEP is clicked, your key is listed under WEP Key 1.

6) If WPA is clicked, your key is listed under Passphrase.

In general, to reset the D-Link to the Factory Default Settings, please follow these steps:

1) Turn off the router

2) Locate the Reset button on the back of the router.

3) Use a paper clip to press the Reset button and power on.

4) Hold for about 5 seconds (don't hold too long) and then release. (Or, release when M1 and M2 flash at the same time.)

5) After you have completed the above steps, the router will be reset to the factory default settingsBest of luckthanks

Try this link to connect Kindle to the wireless network.I hope this will help you.

If the default password on the D-Link has been changed then -To reset the D-Link back to the default settings -Press and hold the RESET button at the back of the router with the power ONuntil the LEDs flash at the time the release the RESET button. (firmware version was 3.00, and upgraded to3.05)Connect a LAN cable from the D-Link to your laptop/computer'sLAN port, open the browser on your laptop/computer and enter the D-Link's configurationURL..http://192.168.0.1The default login = adminThe default PW = blank (just press Enter)You can now change the default adminpassword.You can now configure the wireless settings. Now configure the wireless card in your computer/laptop withthe router's wireless settings.To secure your wireless network from unauthorized access,please click on this link and follow my instructions :-http://www.fixya.com/support/r3559128-wireless_router_security

if you are referring to the wireless security passcode pin number , its usually written on the bottom of the router.

When you get the "Enter the correct password above and then type the characters you see in the picture below." as part of the login this is the non stndard (i'm not yet sure why this appears) but I found the solution to get the standard login screen is to use http://dlinkrouter/login.asp instead of the ipaddress. AT least it worked for me.

You need to go into the D-Link wireless settings to get the SSID and encryption settings and configure the wireless card in the different computer with these settings.Connect a LAN cable from the D-Link to your laptop/computer'sLAN port, open the browser on your laptop/computer and enter the D-Link's configurationURL..http://192.168.0.1The default login = adminThe default PW = blank (just press Enter)You can now change the default adminpassword.You can now configure the wireless settings. Now configure the wireless card in your computer/laptop withthe router's wireless settings.To secure your wireless network from unauthorized access,please click on this link and follow my instructions :-http://www.fixya.com/support/r3559128-wireless_router_security