20 Most Recent Kenmore 44072 Front Load Washer - Page 9 Questions & Answers

If you try using youtube and putting replace dispenser tub for 90 series kenmore washer it will give you lots of videos to watch and learn

A fuse could be blown or a circuit breakers has tripped. The delay start button or the control lock feature has been turned on.

you can try jumpering the door switch and bypass the door lock system, see pics

First try resetting it..Since Kenmore washers have capacitors and other components which hold the charge for some time, it is recommended to keep your washer disconnected for at least 5-10 minutes, so the residual charge is drained. After waiting at least 5 minutes, power up your Kenmore washing machine again. Conclusion When your Kenmore washing machine displays a phantom error code or some other issue, resetting it is the best way of action. Hopefully, after following the instructions mentioned above, you'd be able to reset your Kenmore washing machine. If that doesn't help you may have a broken or disconnected suppension rod..https://www.repairclinic.com/ProductDetail/1416243?symptoms=38

the clutch should be checked for wear by spraying water from water bottle on it when you run the spin load and it should not show any steam or sizziling, you can also remove the clutch and try to hand spin the inside while holding the body it should not be able to spin easily, should be difficult to move. should be a tight fit, im sending more pics but fixya giving me problem s sending them, also check the motor coupler for damage or broken pieces on floor. also test the door switch by jumpering it,

here are some pics to help you locate problem areas to check

The washer's F20 code indicates that it hasn't filled to the expected level in the usual ~8 minutes. Does any water actually enter the washer? If it doesn't, then the inlet valves are not opening. If you get a trickle of water, then the valves may be clogged. In both cases, replacing the inlet valve solves the problem. (For a slow fill, sometimes using household vinegar can break up the calcium carbonate. This is usually a temporary solution.) If the water enters the tub and then the pump starts draining the unit, adjust the drain hose. You need the end of the drain hose higher than the water level in the tub. If water is pouring into the tub and it fills normally, then the system that detects water flow is damaged. This involves a pressure switch that has an air hose connected to part of the sensor. Check if this hose is damaged or clogged. Blow out the clog and see if that fixes the problem. Otherwise replace the pressure switch. I can't find a 110.47081 parts diagram. Check your washer for the model number. There are probably three additional digits to the model suffix. I hope this helps. Cindy Wells

Usually if you cut the power at the wall, it will release the Lock solenoid.

I find no mention of a lint filter in the Manual. Ck here... https://c.searspartsdirect.com/pd-content/is/content/Sears/L0705087

Your'e missing some numbers. That's only a partial Model #.

Check here... https://www.repairclinic.com/RepairHelp/How-To-Fix-A-Washing-Machine/47-6-607241-/New/Kenmore-Washer-Won-T-Spin-Or-Agitate-417-43142200 Give their techs a call at their 800# before throwing parts at it. Best to you.

On average, washing machines use 19 gallons of water per load, and the average household runs between 5 and 6 loads per week. Based on those figures, most washers use up to 5,605 gallons of water annually. Front-load washers use an average of 12.5 gallons of water per load, while top-load washers average 19.6 gallons per load. Older top-load models manufactured decades ago use 40 or more gallons of water per load. Possibly reading the meter incorrectly... ck here... https://plumbingsniper.com/how-to-read-a-water-meter/ My 1.5" water line to fill my pool puts out 12 gallons a minute it would take 45 minutes running full out to put out 530 gallons. Best to you.

Possibly this.... https://www.appliancepartspros.com/lg-pcb-assembly-main-ebr75639504-ap5681030.html But give them a call at their tech #877 before ordering.

Could be several things. Check this link and give them a call at their 800 tech # to confirm what it might be before throwing parts at it. https://www.repairclinic.com/ProductDetail/939978?symptoms=66

Question edited for clarity. 2 Duplicate questions deleted. Refresh page to see your question.

How to Find the Age of a Kenmore Washer

Hunker https://www.hunker.com > ... > Washer & Dryers Locate the serial number on a Kenmore washer made by Whirlpool. The second letter of the serial number identifies the year the machine was manufactured. For ... More here, but you need Model Number and Serial Number https://www.google.com/search?q=kenmore+washing+machine+serial+number+lookup ..

Is the lid actually locking when lock light comes on? If not, replace lid lock

Washing machines will not spin until they have emptied most of the water from the drum. I would check the outlet pipe is clear and the pump runs with no obstruction first.

https://www.youtube.com/watch?v=I0ECIx4KujQ https://www.youtube.com/watch?v=b977m2jXcog

Hello. I'm a little confused at the description of the problem. You indicated it, "will not agitate during wash cycle or spin during the spin cycle." But later in your description you indicated, "It will however, drain and spin after wash cycle and during the rinse cycle." I'm not sure if you description was an error but it sounds like you will need to replace the coupling which is part number 285753A.

Press, High temp wash, heated dry, High temp wash, heated dry, High temp wash, Heated dry The panel should all light up at which point you need to press cancel. This will reset the control board if it can be reset. If you do not have a "heated dry" button use "saver dry" or "air dry"