20 Most Recent
Sony DVP-SR200P DVD Player - Page 8 Questions & Answers
Hooked up dvd sr200p to
If you are connected useing the component video cords (red,blue,green,red,white) it sounds as if you have the red,blue or green cords connected to the wrong color of jacks on the back of the TV or the DVD player, recheck your connections.
If all is good there, maybe one of those cords are bad?
The Sony DVP-SR200P DVD player is on the bottom end of their model line up, and you may have received a bad one right out of the box!
GOOD LUCK !!
HOW DO i UNLOCK THE CODE
Ensure the child lock feature is disabled. Attempt to open the disc tray. If the issue is not resolved, turn off the DVD player. Unplug the power cord from the electrical outlet for 30 seconds. Plug the power cord back into the electrical outlet. Attempt to open the disc tray. If the disc tray still does not open, simultaneously press the POWER + STOP + EJECT buttons.
If the disc tray still does not open, simultaneously press the DISC1 + STOP + EJECT buttons or the RETURN + ENTER+ POWER buttons.
If the issue is still unresolved, service may be required. The Sony eService Web site at http://eservice.sony.com/ can assist you in obtaining service from a Sony Service Center or locating a Sony Authorized Servicer.
Cd compartment wont open and it is locked dvp
Ensure the child lock feature is disabled. Try Power resetting the Player.
Turn Off the player and remove the power plug from the wall outlet for 1 minute and reconnect it and check the operation.
If the disc tray still does not open, simultaneously press the POWER + STOP + EJECT buttons.
If the disc tray still does not open, simultaneously press the DISC1 + STOP + EJECT buttons or the RETURN + ENTER+ POWER buttons.
If the issue still persists, service might be required.
DVP-SR200P it's limited to a
Did you try this?
1. Switch on the DVD player
2. Open the disc tray (with no disc inside)
3. Using the remote, tap in the following code - 2812
4. Highlight the region code that appears
5. Change the region to 9 for Multi-Region by pressing the 'Enter' button
6. Press 'Clear' to exit the region menu
I purchased dvds from ebay and they will not play
Turn on the unit with the remote controller, Wait until "no disc" appears in the unit's display. Press the keys: PAUSE, 3, 1, 4, 1, 5, 9. And "CODE" will appear in the display. Press the number key that corresponds to the disc zone you want to play within the next 5 seconds:0: All regions / 1: Region#1 / 2: R#2/... and so on. Then, within 5 seconds, press: PAUSE, POWER... and voilà. If you don't have good results, disconnect the equipment and repeat.
Or
Put your player in standby mode and then enter: [[0] [ENTER] Default Default region code [1] [ENTER] or [UP] [ENTER] Region 1 [2] [ENTER] or [RIGHT] [ENTER] Region 2 [3] [ENTER] or [DOWN] [ENTER] Region 3 [4] [ENTER] or [LEFT] [ENTER] Region 4 [5] [ENTER] or [TITLE] [ENTER] Region 5 [6] [ENTER] or [DVDMENU] [ENTER] Region 6 [7] [ENTER] or [RETURN] [ENTER] Region 7 [8] [ENTER] or [DISPLAY] [ENTER] Region 8
Or
Put player into standby modes by pressing power button on remote control. Then press Title button. Press Clear button. Press Power button.
I found these codes for all the other DVP-SR series players, yours was not listed but I thought was worth a try.
I just purchased a Sony
Try to go under the settings in the dvd player. Be sure all the setting are set up according to your TV.
Sometimes if you dont have it set to N. American standards it can output like that. Be sure its set to "NTSC" if you live in N. America or Japan. If you live in Europe be sure its set to "PAL".
Let me know If this is not a issue in comments and I will help you further but I think this is it.
How do i turn off captionic
Cycle through caption settings until it goes off, each time you push the caption button it goes to the next caption setting then finally back to the the begining.
I need the TV code
Here are the codes for your Sanyo TV.
3-digit codes:
004/ 013/ 049/ 108/ 110/ 180/ 209
/ 002/ 006/ 071/ 128
4-digit codes:
0154, 0159, 0000, 0080
One of these codes should work.
Good luck!
Ineed 2unlock my sony dvd sr 200
Go to my "computer". Klik on DVD driver. Klik on properties. Klik on DVD region. Look in for country. Select. Usually allowed 4 changes after 1st factory setting.
Need code for insignia tv
Many remote control codes can be found at InsigniaProducts.com. Search for your Insignia product model number and click on the Support tab.
NO color - only black
Hi,
If your Sony DVP-SR200 is under warranty then call Sony to get replacement, number would be written on related warranty documents.
No parts/ board are available for this model and Sony offers replacement only. And if its out of warranty, buy new dvd player.
hope this info will help you.
Thanks.
I just purchased a sony
If you provide more information I can be more helpful. What is the model of av receiver and tv? Please describe exactly what is not working and what you have done so far.
Not finding what you are looking for?