Husqvarna Rose - Answered Questions & Fixed issues

This problem for your machine is the motherboard problem, you can contact [email protected]

Hello The machine is indicating that it "wants" you to move the hoop into position P2 or P3 according to what is blinking. This is normal. Once that colour is completed stitching, the machine will communicate again for the nest Position. Happy Stitching Sewingirl/

The Rose has a sensor on the presser bar assembly that is giving you the grief. The machine thinkss the presser foot is in the raised position.There is a small metal flat spring that has gone bad and causing the error. Find an autorized service center to repair the problem.

What Viking is it ? Have you cleaned between the feeders? If all is clean, try this test. Remove needle. Turn hand wheel so that feeders are up. Put fabric in machine. Lower presser foot. Make sure presser foot pressure is set at normal. Try pulling the fabric towards the front of the machine. It should be hard to pull. If it is easy to pull you need new feeders. They are worn down.

It thinks the presser foot is in the up position. Will need to be repaired by experienced service tech (preferably a certified Viking service tech). There is a clamp that may just be out of place or it could be more involved. Good luck.

you probably need to have an authorized Viking repair person check your machine.

When the bobbin is wound with too much tension it crushes the inside and won't come off the spindle. You need to pull all the thread off the bobbin and replace it. Make sure you wind the bobbin at slow speed and the presser foot is up if you wind through the needle.

Take a small screw driver and slide it under the bobbin and apply a little pressure and it should pop off.

You might try eBay.

Try this link for free manual for the Viking Rose machine - http://new.husqvarnaviking.com/SiteMedia/Products/Machines/Support/Rose_605_manual_EN.pdf There are 2 models called 'Rose'. The original Rose is the manual above. The newer Rose is called the Eden Rose. You can find most user manuals for Viking machines on their website. Here's how: website: http://www.husqvarnaviking.com/us Go to bottom of page on righthand side and click on 'Machine Updates'. If your machine is not listed click on 'All Machines" Scroll down until you find your machine and click on the name of your machine. The link should take you to a page with a picture of your machine and a link to Download the manual which is a PDF file. Good luck.

Your user manual should explain how in detail with pictures. It is sometimes hard to get the bulb out without breaking it. But try this - With machine unplugged/power off lay machine on it's back. Locate the light bulb. You probably have a little rubber device in your accessory case that has a suction cup on each end. One end will say In and the other will say Out. Use the suction cup to grab the bulb and pull straight out. Use the other end to install the new bulb in the machine. If you need a manual - Try this link for free manual for the Viking Rose machine - http://new.husqvarnaviking.com/SiteMedia/Products/Machines/Support/Rose_605_manual_EN.pdf There are 2 models called 'Rose'. The original Rose is the manual above. The newer Rose is called the Eden Rose. You can find most user manuals for Viking machines on their website. Here's how: website: http://www.husqvarnaviking.com/us Go to bottom of page on righthand side and click on 'Machine Updates'. If your machine is not listed click on 'All Machines" Scroll down until you find your machine and click on the name of your machine. The link should take you to a page with a picture of your machine and a link to Download the manual which is a PDF file. Good luck.

try these sites
sew usa
sewing manuals.com
ebay

Try this link for free manual for the Viking Rose machine - http://new.husqvarnaviking.com/SiteMedia/Products/Machines/Support/Rose_605_manual_EN.pdf There are 2 models called 'Rose'. The original Rose is the manual above. The newer Rose is called the Eden Rose. You can find most user manuals for Viking machines on their website. Here's how: website: http://www.husqvarnaviking.com/us Go to bottom of page on righthand side and click on 'Machine Updates'. If your machine is not listed click on 'All Machines" Scroll down until you find your machine and click on the name of your machine. The link should take you to a page with a picture of your machine and a link to Download the manual which is a PDF file. Good luck.

Your local Husqvarna Viking dealer can order one for you.

Are you sure the floppies are corrupt? I suggest you locate a computer professional that sells used computers and tell them what you want done. I'll bet they can transfer the files to a new hard drive for your old computer or to another computer. Be aware that the older embroiderary software is not compatable with Windows Vista, 7, or 8 so don't plan on getting a new computer as part of this update.

Is the foot pedal not returning to the off position? Try disconnecting the foot pedal. If the machine stops running, then your problem is in the foot pedal. If it keeps running, then your control board is bad.

The bobbin winder may need a new bobbin tire. Does the bobbin winder move over like normal?

The software has been upgraded many times and now uses a USB port. Which version of software and which disc are you missing? I may be able to help.

Slacken the tension off

it would be a good idea to have the computer part of the machine checked