20 Most Recent Janome 8080 Computerized Sewing Machine - Page 6 Questions & Answers

SP means that the bobbin winder has been pushed to the right in preparation for winding the bobbin. Just click the winding post to the left till it clicks, and the stitch number will be displayed.

make checks on the bobbin case that holds the bobbin beneath the machine it could be broken or too tight then you need to slacken it a bit so that thread can flow easy there after oil your oil the machine if the bobbin case lever is broken or bent replace it.also adjust tension disc.good luck.

1. Power Off: Turn off your machine completely. Make sure it's not just in standby mode but completely powered down.
2. Unplug: Disconnect the power cord from the outlet. Wait for about 10-15 seconds to ensure all power is drained from the machine.
3. Plug Back In: Reconnect the power cord to the outlet.
4. Power On: Turn on your Janome 300e and see if the screen is responsive now.

If the issue persists even after performing a reset, there might be a more significant problem with the machine's software or hardware. In such cases, it's advisable to contact Janome customer support or a certified technician for further assistance. They may provide additional troubleshooting steps or recommend servicing the machine.

Page 27 of the manual refers. (by the number on the pages, not at the top), use CTRL+F and type the word 'Number'.

Instruction Book

Janome https://www.janome.com > embroidery > mc550e PDF q Stitch back key w Stitch forward key e Stitch count r Total number of stitch count. The pale blue bar in the stitch count window is the progress bar. The ... 76 pages ..

Are you having any problems moving the needle bar with the hand wheel? Make sure that the presser foot is up and the needle bar is fully up. Then redo the top threading for the machine. Try unplugging the machine and blowing any loose debris out of the needle bar area. (I'd suggest compressed (canned) air or equivalent to minimize excess moisture in the electronics.) Also check if the machine gives the same message with the presser foot and needle down on restart. If the problem persists, then the issue is likely to be a faulty control board. I don't know if any sewing machine repair technicians still have spare boards. They aren't on the in stock parts at two vendors that I know. I hope this helps. Cindy Wells

I would look on the manufacturers web site; https://www.janome.com/blog/need-a-janome-manual-many-available-for-download-here/

If the top tension is on 0 I suspect the problem begins in the bobbin, make sure first of all the bobbin is turning anti clockwise in the bobbin case, when you pull the thread through the bobbin case there should be slight resistence, if it is too loose turn the screw on the bobbin case clockwise about a quarter of a turn to tighten, if it is not making muh difference you may have fluff stuck under the spring on the bobbin casem take a fine sewing needle and slide it under the spring to see if you can get any fluff out, top tension about 4 or 5

You would have to remove the top cover. https://www.google.com/search?q=janome+jem+lite+639+remove+top+cover ..

I have the Janome CHJ-3 Kwiknit Knitter and am having some problems with it. Purchased this machine some40 years ago and used it an awful lot and was always very happy with it. After storage and loaning it out, it now does not work. Needs a service I suppose which I would like to do myself. Does this machine have a sponge bar? Also I can copy the manual and send it to you - please let me know.

You can download the Artistic Designer program from Janome, https://www.janome.com/products/software/ . However, it will not work unless you have purchased a license key from a dealer. For other Janome software, only updates for supported software are available: https://www.janome.com/support/general-support/software-support/ . You'll either need the program to have been installed on your computer or to put the CD in an optical disc drive. If your current computer doesn't have an optical disc drive, you can get a USB optical drive from Amazon or any other shop that has electronic/computer parts. USB DVD read/write drives are under $50 even at most shops that don't discount accessories. You may need the USB type C (M) to USB type A (female) adapter with some of the newest models (laptops and tablets). I hope this helps. Please add a comment with the name and version of your software for further assistance. If your software is no longer supported by Janome, there are some third-party embroidery editing software packages. One is https://www.embird.net/ . Cindy Wells

Your space is not formatted correctly to the size of the hoop. For example if the hoop is 5x7 your design has to fit within that space, and the space cannot be bigger than 5x7. Strange but true and it will fix the reboot and shut down issue.

All available Janome user manual are here https://www.janome.com/support/manuals/ However you can use this manual, it may help you. inst-book-mod-15.pdf (janome.com)

A new old machine for you I assume.For older mechanical only machines, reverse stitch is an exaggerated long stitch length that changes the angle and contact time of fabric to the feed dogs. Try setting stitch length to minimum and straight stitch. Check feed dog up/down is functional (if featured). It could also be the reverse linkage is simply stuck and the machine is in need of a thorough clean/lube.I looked for a manual but so far have not found. I'll append if I find.

See troubleshooting section on page 49 of manual. It may help. *4618-QC (janome.com)

It migHt just be the LCD screen controller. RotAting knob inside top front near bobbin winder bobbin holder. Rotate it gently as very sensitive

Question edited for clarity. Question moved from Cars and Trucks category. Of course. It is the absolute worst thing to do to a sewing machine, leave a machine in a closet for 3 years. It oil will have congealed and gone rancid and any lint that was in there will have set hard. It will need a good clean, lubrication, service and timing done. Plus it is electronic, so I hope your close in nice and dry and warm with no moisture. Even if you don't use them, then need cleaning and oiling every year. https://www.janome.com/machines/embroidery/mc11000/ ..

Question edited for clarity. Please don't type in all CAPS, it is considered SHOUTING and is harder to read. Sewing machine tension is a delicate tug of war between the bottom Bobbin tension and the Upper tension to put the loop between the 2 layers of fabric. You set the Bobbin tension first and the the top tension depends on the fabric and the thread used. Your Bobbin tension is very very loose to be not tensioning at all or the top tension is too loose.

Adjusting The Tension - Janome Memory Craft 6500 ...

ManualsLib https://www.manualslib.com > ... > Instruction book Janome Memory Craft 6500 Professional Manual Online: balancing thread tension, Adjusting The Tension. Correct Tension: The Ideal Straight Stitch Has Threads ... Best video on tension

Question edited for clarity, the name 'Jerome' to 'Janome'. Question moved to maker category. If it is a manual machine, something has come loose. If it electronic, you may be able to reset the control board. They need servicing every 18 months to 2 years irrespective of how often you use them. You are the only person to have this error. https://www.google.com/search?q=janome+sewing+machine+adds+a+zig+zag+to+straight+stitches ..

Janome Overlocker model 8002DX

Do you have it set to Embroidery Mode? The feed dogs are lowered and stationary. https://www.google.com/search?q=usha+janome+allure+embroidery ..