Juki HZL-E80 Computerized Sewing Machine - Answered Questions & Fixed issues
User manual
hi there
i don't know how to upload at fix ya but you can send your email and i will send to you user manual for JUKI HZL-E80 immediately.
thanks and regards
ASHRAF
CAIRO - EGYPT
[email protected]
1/7/2014 6:15:59 AM •
Juki HZL-E80...
•
Answered
on Jan 07, 2014
•
231 views
My Juki HZL-E80 won't turn on
no, the light bulb won't cause the machine not to work, check the power cord to see if it's plugged into the machine correctly, if it is then the machine needs to be checked to see if it's the powercord or the on off switch or the machine it's self
10/15/2012 4:44:49 PM •
Juki HZL-E80...
•
Answered
on Oct 15, 2012
•
322 views
Dirty thread
hi there,can you check please that area around lower needle bar bushing? maybe some oil drop from this area.- check the adjustment screw for lubricate hook from down maybe need to decrease the amount of oil how lubricate the hook by turning to minus direction.best regards
4/7/2012 12:51:25 PM •
Juki HZL-E80...
•
Answered
on Apr 07, 2012
•
1,225 views
How do i stop juki ddl from top skipping stitches?
Hi. Skipped stitches are usually caused by a mismatch in your thread and needle. Wrong thread type, wrong needle size, or even old thread can cause skipped stitches. If all else fails, change the needle. If that doesn't work, clean the machine. Sometimes just getting rid of all the lint and giving her a good oiling does a world of good.
Let me know if this works.
Robbie
3/23/2011 1:11:36 AM •
Juki HZL-E80...
•
Answered
on Mar 23, 2011
•
1,067 views
Double needle use on Juki HZL-E80
if the machine regular needle threads front to back NOT side to side, you can use a double needle. simply pass both threads thru all the same slots (thread one at a time so they don't get twisted up) then just before the needles, leave one out of the thread guide just above the needle. you may have to loosen the top tension SLIGHTLY, like a half number. and do NOT use a zig zag stitch without first hand cranking it thru the cycle to be sure the needles clear, or you'll make a 5.00 mistake (the cost of the double needles!)
6/16/2009 6:58:39 PM •
Juki HZL-E80...
•
Answered
on Jun 16, 2009
•
461 views
Hole width
After putting on the buttonhole foot, you lower the foot, put in the size button you want into the button hole foot. Lower the button hole lever all the way (so machine does not blip) Then the machine automatically sets the length and width of the button hole...you can adjust the length and width manually by pushing the button on the top right hand part of the machine above the LED screen the top one is stich length the other is stich width....if you put the levers to the left it will be the smallest stich length or width...if to the right it will be the largest stich length or width the machine allows. But, really the machine automatically does this for you...so I don't see the need to do it.....but you can....BBill01
5/31/2009 12:07:42 AM •
Juki HZL-E80...
•
Answered
on May 31, 2009
•
188 views
Buttonhole problem
Hi,
When doing the button hole....after installing the button hole foot and lowering the foot....and adding the button so the automatic button hole size is determined...you lower the button hole lever it will touch the back of the button hole foot. this holds the button hole foot in the proper position...if this lever is not all the way down...the machine blips at you...check to see that it is down all the way...I hope this helps you..It truly does all that it advertises and is a great machine...BBill01
P.S. you can adjust width and length of the stich also...see instruction manual. pg 28-30
5/30/2009 11:56:16 PM •
Juki HZL-E80...
•
Answered
on May 30, 2009
•
607 views
Thread continues to jam
Hi, my wife and I just bought a Juki HZL-E80... I love the machine. I had a problem like you discribe...This problem can come from two sources...one the bobin has been installed improperly. ...or been wound incorrectly by not haveing adjusted the Bobbin tension ...I did the tension adjustment with the screwdriver supplied with the machine accessories. Also...this is a biggie...the auto matic needle threader works great...but I discovered that when I preformed this function..that I over looked the thread holder that keeps the thread even with the needle....so, the solution is to thread the needle then be sure to check that the thread coming down from the spool is placed behind the little wire holder above the needle...I hope this helps you ...because it is a wonderful machine.....Bill & Donna Bramble...Caldwell Idaho...
5/30/2009 9:44:37 PM •
Juki HZL-E80...
•
Answered
on May 30, 2009
•
341 views
Not finding what you are looking for?