20 Most Recent Necchi 6015 Mechanical Sewing Machine - Page 2 Questions & Answers


I find that re-threading both top and bottom threads fixes the problem. Sometimes the thread has not gone through the tension springs properly. try a new needle too.

Necchi 6015... | Answered on Dec 08, 2010


I have 2 necchi sewing machines & have the following feet
1.all purpose foot
2.zipper foot
3.buttonhole foot

sewingpartsonline.com has necchi parts

Necchi 6015... | Answered on Dec 02, 2010


have you cleaned under the needle plate
change the needle
make sure the thread has not come off the thread take up lever
some thread & needle don't work togeather--try this
Cut 6-8 inch piece of thread of the spool you are going to use for your project
Take the needle you are going to use for the project
& insert the thread thru the eye of the needle
& lift one end of the thread to a 45 degree angle
& if the needle is the right size for the thread it will slide down the thread
But if the needle hangs on the thread you need one size larger needle for the thread

Necchi 6015... | Answered on Nov 21, 2010


If you have a zig-zag stitch on your machine, you have the capability of using a twin needle when using a STRAIGHT stitch. The width between the needles is the same as the width for the z-z stitch but you won't be using that stitch. Only the straight stitch.

Necchi 6015... | Answered on Aug 24, 2010


If the machine is old, I would get a new one. It shouldn't move and the fact that you can depress it easily sounds like it's defective.

Necchi 6015... | Answered on Aug 23, 2010


Hi. If the bobbin thread is coming up on top, then the upper tension is too tight. Try loosening it.

Hi. The best way to adjust your tension is to use good-quality thread, a size 12 needle, and different color threads in the bobbin and on top. That way, it's easier to see which thread is loose. Sew a few inches, check, and adjust (make sure the pressure foot is DOWN). Stitch a few more inches, recheck, and adjust some more. Just move the adjustment knob a little bit each time.

You might also want to use a bit of unwaxed dental floss and floss the tension disks. That helps get rid of any old lint and pieces of thread that build up in there.

As a last resort, you might need to adjust your bobbin tension. There is a very small screw on the bobbin case that tightens/loosens the spring/lever. If you need to adjust it, only move the screw a tiny bit. But, like I said, this is only a last resort--almost all adjustments can be done by adjusting the upper tension.

Hope this helps!

Robbie

Necchi 6015... | Answered on Aug 12, 2010


i was able to find one at www.ifixmachines.com

Necchi 6015... | Answered on Feb 15, 2010


nake sure the machine is threaded proiperly with a good mercerised thread no thicker than a number 40, make sure the needle is in the correct way round, top tension about 4 or 5

Necchi 6015... | Answered on Oct 26, 2009


You may need to get a scrap piece of material to lead off with or hold on to your thread and gently pull it to start your material.

Necchi 6015... | Answered on Aug 09, 2009


If the belts are not tight enough they will slip, they should all be fairly tight but not like a piano string if you know what I mean.
As you do not describe what the machine is doing wrong I can not really say any more at present, except make sure there is no oil on the belts and the machine has no tight spots when you turn it over by hand.

Necchi 6015... | Answered on Jul 07, 2009


Just call 1-800-525-9987 and ask for Parts or Service - these guys are the sole importer of Necchi and can answer your questions - sorry i haven't found a download for a manual in english - if you want in italian is available for the 6000 series here: http://www.necchi.it/_italiano_/scheda.asp?param=70&ID_MARCHIO=1 but the guys on the number at the top will be able to tell you the best place to get one. Hope this helps :)

Necchi 6015... | Answered on Feb 27, 2007


When I repair a machine I use triflow oil on any metal to metal rotating part ie back and forth. On metal gears I put the tri flow grease. You can use it on plastic gears although sparingly. the nylon gears were design for quietness and were not recommended for grease. You want to get the old grease off as best you can. If it goes up and down or side to side then oil. If it continuously rotates then grease. Exception those bearings that have an oil hole vs a grease cap.

Necchi Sewing... | Answered on Oct 16, 2019

Not finding what you are looking for?
Necchi 6015 Mechanical Sewing Machine Logo

44 questions posted

Ask a Question

Usually answered in minutes!

Top Necchi Sewing Machines Experts

Tally Girl
Tally Girl

Level 3 Expert

1134 Answers

Douglas Plant
Douglas Plant

Level 2 Expert

222 Answers

Irene Tulloch

Level 2 Expert

498 Answers

Are you a Necchi Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Necchi Sewing Machines

  • Necchi Sewing Machines

Most Popular Question

bobbin thread straight across

  • Sewing Machines
Loading...