Top 20
Singer 2732 Mechanical Sewing Machine Questions & Answers
Need Owner Manual
Search the internet for:
Make + Model + the word "Manual"
or contact the manufacturer Support number.
...
How to adjust bobbin case for proper movement.
- Using a doubled piece of fabric similar to what you have in mind for your project, sew a seam on the diagonal-pulling the fabric on the diagonal to break the threads. (Ideal tension would either break neither thread or break both threads. So, a single breaking thread signals that the tension needs adjusting.)
- Snap out the faceplate to remove it & to gain access the bobbin area below the sewing needle.
- Remove the bobbin case & bobbin-lifting the hinged latch that you would to wind a new bobbin-leaving the bobbin in the case. (You need it in there to feel the tension as you adjust it.)
- Using a small screwdriver, very slightly turn the screw on the side of the bobbin case clockwise to increase tension; counterclockwise to decrease tension.
- Pull the bobbin thread while you hold the bobbin in its case & feel the thread's tension. Too tight of tension would prevent the thread from dispensing (& possibly break), but too loose of tension would allow the bobbin to fall out of its case.
- Return the bobbin case to the sewing machine & close the faceplate.
- Repeat this whole routine from Step One on the doubled fabric. Stitching should run along both the top & the bottom in the same way-locking in the center. A diagonal pull of the fabric should show which thread(s) break(s). Repeat Steps Two through Four to only adjust the screw aside the bobbin case in order to allow the threads to lock in the center of the fabric with both threads having the same break or no-break result.
My singer 2732 sewing machine will not pick up bobbin thread
There are three causes. Make sure your needle is all the way up in the needle clamp, and the flat side it on the back (if your bobbin is in the front of the needle).
If it is, then your timing is out of synch, and you will need to get a technician to fix it.
The bobbin is bunching up when
try changing the needletry rethreading the machine top and bobbin with a different threadtry a different bobbin--and then make sure the bobbin is turned theright way.make sure the to thread has not come off the thread take up lever
My neddle keeps bending the side and breaking
Needle breaks
1.the needle is damaged
2.the needle is not correctly inserted
3.wrong size needle for the fabric
4.the wrong foot is attached
5.the needle clamp screw is loose
6. Top tension is too tight
7. Machine could be out of time
How to put the tread in the needle of a 2732
the singer website has a PDF free manual download
Go to the singer website
Go to the home page
At the bottom of the page look for instruction manual--click on it
It will take you to another page
In the box put the model number (example 2732 ) & click search
second one is free
My bobbin on my Singer 4562 keeps bunching up the
If you have the black bobbin case you must make sure you use only a good mercerised thread, there should be enough gap between the edge of the bobbin case and the silver adjuster to allow the thread to pass through, if there is not then you must slacken off the two screws and move it over a fraction.
How do you adjust the
Tension is adjusted with the tension dial on the right side of your machine.You would adjust the tension to your comfort. Use a piece of material to practice on, and tighten or loosen your tension till your threads look just right. If they are to tight your material will bunch up, if they are to loose you will have thread loops or very loose threads. As you get to know your machine this will come to you as easy as driving a Model T Ford. GOOD LUCK.
My top thread is making
I believe your tension is to tight. Loosen your tension dial, while using a piece of scrap material. Continue till you achieve tension you are happy with. GOOD LUCK.
How do you thread the
Sewing machines. All the manufactures copyright their manual. They know that you need a picture. It'll cost ya
$12.
:o).
THE TOP THREAD IS BREAKING
Loosen your tension dial till the problem is resolved. Work on a piece of scrap material to achieve this . GOOD LUCK.
I have a Singer 2732.
http://www.singerco.com/resources/threading.html, this will tell you how to thread. I am thinking that you do not have the cap that you put over the thread spool to stop it from falling off. Until you can get one, how about taking the top of an empty pill bottle and making a hole in the center and sliding it on the spool pin. Then call Singer at 1-800-4singer and order the real thing, you can also ask them questions on operating the machine. It looks like they do not have a manual for your model for free, it is $15.
Not finding what you are looking for?