Top 20
Minolta Di3510f Bizhub Copier Questions & Answers
C0500
To reset Error codes C0500 and C0501, perform the following steps.
1-Turn the machine "OFF".
2-Press the "STOP" button on the basic panel.
3-Keep the button pressed and turn the machine "ON".
4-Do not release the button, until the machine warm up.
5-After few seconds Error code will remove and machine will reset.Basic menu will show no error on LCD screen.This means error code has been removed and photocopier machine is ready to use.
How do I change the drum on a bizhub 3510
First ensure fax line and and network cable is disconnected (If no FAX or network dont worry) dont want any print jobs or faxs arriving before you run Developer and drum checks after replaceing both.. Second go to the service mode and clear the drum and developer counters touch end then power off the using main power switch left hand side rear. You will be replacing both do not just replace the drum. Ensure your drum comes with what is called a drum cleaning blade, along with your developer. Secondly open the right side door and remove the Image unit. Dissamabley the image unit four silver screws two per side. Then pull each side apart from the base and lift up. T change developer remove the 3 alummin screws fro the base top. Then dump the old developer DO NOT USE A VACUUM CLEANER THE STATIC ELECTRICITY WILL DESTROY THE SENSOR AT THE BOTTOM OF THE DEVELOPER UNIT!!!!!!!!!! Turn the gears on the side so that large roller that runs along th\e front of the developer unit turns downward. keep turing it unit all of the old developer is out. DO NOT USE WATER OR WET RAGS to cleanup use a brush. Add your new developer. One Bag only. Reassamable. Now for the Drum. Remove both side covers one side has small plasitic been so be careful. Reove drum remove three screws to remove old cleaning blade this section you can use a vacuum clean turn the gears to get the hold section clean. install the new cleaning blade and drum DO NOT TOUCH THE DRUM use only the side gears. Replace the SCTRON Grid and Charge Corona UNIT. REassaembly Image Unit.Then POwer up the machine, Enter service mode and run Fuction F8. Do not may copies or prints before this or you will have to buy new developer again.
IF YOU REALLY WANT TO DO THIS?????? HAVE SERVICE TECH COME OUT AND DO THIS Btw, I’m available to help over the phone in case u need at
https://www.6ya.com/expert/normanj_7893313f0751935f
Error code c0990
Bottom draw lift motor is jammed or burned out. Good chance its a bad gear located behind several gears in the front of the draw. This particular Gear sometime gets round out. When originally designed as a half moon. Btw, I’m available to help over the phone in case u need at
https://www.6ya.com/expert/normanj_7893313f0751935f
Minolta di351f c0070
Power off the machine. Then remove the toner bottle be careful the hole might be on the bottom toner is going to everywhere. Then close the toner cover and turn on the machine. Let the machine go through it normal routine. When it asks for toner install the toner install it correctly. If THE KUNB on the side of the bottle is damage put a new one in that KUNB is what the toner motor uses to turn the bottle if it damage you get a code. If that does not work you mite have a bad motor or the home sensor or acurator for the toner bottle is bad worse case the control board is bad Btw, I’m available to help over the phone in case u need at
https://www.6ya.com/expert/normanj_7893313f0751935f
Error c0ba0
Your finisher elevation motor is failing or the sensors that monitor what and where the output trays are doing on their way up and or down. Tray hit some boxes stored under the bottom tray? some one leave a trash can and the tray hit it? Some one drop something on the tray. Away requires removing the rear finisher cover remove the elevation motor assy. BE CAREFUL if removed the TRAYS will FREE FALL. have to know how to handle that!!!!.Ensure trays move easy and does motor turn might have a bad motor. Btw, I’m available to help over the phone in case u need at
https://www.6ya.com/expert/normanj_7893313f0751935f
How do I scan from my Bizhub Di3510f to my computer?
You need to go onto the user interface of the machine and add your network settings. this is done by entering the IP address into your search bar and then going to have to enter the details into the relevant boxes
ERROR CODE C0860
DID you mean C-0960!!! C-0860 does not exist in the service manual. Check your bypass tray right side. For something jammed if no need to get a tech out for Konica Minolta. I believe there was a technical bulletin issued in regards to that error several years ago. Btw, I’m available to help over the phone in case u need at
https://www.6ya.com/expert/normanj_7893313f0751935f
Error C-5102 minolta C450
C5102: Main Motor's failure to turnRelevant Electrical PartsMain Motor (M1) Mechanical Control Board (PWB-M)DC Power Supply (PU1)Step ActionWIRING DIAGRAMControl SignalLocation (ElectricalComponent)1Check the M1 connector for proper connectionand correct as necessary.- -2Check M1 for proper drive coupling andcorrect as necessary.- -3Check the PWB-M connector for properconnection and correct as necessary.4M1 operation check PWB-M CNDM1-5 (REM)PWB-M CNDM1-8 (LOCK)L-25 Change PWB-M - -6 Change PU1 - - thanks®ards
Not finding what you are looking for?