20 Most Recent Minolta EP1083 CS/PRO Copier - Page 5 Questions & Answers

What did you wipe the drum off with???? That is why you have this problem. You may want to try recleaning the opc with a dry soft rag, also you may want to clean the drum blade... If that dose not solve your problem, you may need to replace the opc & blade... Have you tried to stop the copy before it gets to the fuser unit.. If so, are the marks there???

Make reset by pressing S1 on Board -A keeping the machine ON

toner carrier ratio is off, try adding toner by pressing the toner button on the control panel and insure there is toner in the toner bottle.
If this doesn't correct it the AIDC sensor may have failed

an ep 1083 is an analogue  copier and has no ports

What you mostly need to do is to clean the optics under the copyboard glass the mirrors are mostly dusty... I would use a soft dry cloth to wipe the mirrors off. There is a mirror under the "Black Box" I would also, use a lightly damp rag with rubbing alcoh. to wipe OFF the scanning lamp & reflector. Cleaning the optics should get read of the dark back ground, but the drums are only good for 80k... You may need a new OPC drum & blade. Good Luck

Hi

Welcome to Fixya

Have alook at the webpage by following this link:

http://servicelineat.ro/hplaserjetm5025.html

Scroll down the page for error listing. Unfortunately error 60.40 is not listed. It may help to ring HP service centre for a full error code list.

Hope this helps. Please don't forget to Rate this solution.

Thank you.

COF30 THIS CODE SHOWS THAT THERE IS PROBLEM IN AUTO TONER SENSOR.MAY BE IT IS DIRTY .CLEAN IT PROPERLY .OR REPLACE IT.PROBLEM WILL BI REMOVED.DO NOT FORGET TO RATE A SOLUTION.MIAN JEE

hello sir; You need to replace drum cleaning blade or drum cartridge will be take care of your problem.

you have to change imaging unit

If the machine sees the ADF ( auto document feeder) but does not feed the paper? Does it try to feed the paper? Does it pull the paper is a little and jam? If the machine sees the ADF and it starts to feed the paper but jams --- clean the feed rollers/ tires with rubber restorer or a high alcohol base cleaner. Also a mylar could be pulled into the paper path blocking the feeding of the paper. Take a thin piece of cardboard ( like the devider in a case of pop) and slide the cardboard about 3- 6 inches into the feed just past the feed roller. Gently pull back out and try to feed paper again. If those do not work and the machine does see the ADF, you may need switch, sensor, actuator or feed motor.

First make sure that all the doors/ covers are closed --- not just by looking but push on them. Sometimes over time the switch gets pushed in to far and even though the doors/ covers look to be closed the switch is not pushed in far enough. When you find the switch ( should be a little slot that you see silver through, you can bend it out slightly and gently.

you have to go to service mode to adjust it that's ,technician's job,better looking for a local service provider

why is this still posted?
this was solved

you can disconnect the sorter.if that's all you need

no cods?
can you take lamp out ? check with aom meter .sould have coninuity
hope that help

Not really sure what you are asking?????? It use toner not ink..... Need a little more info.....

i still think its your developer unit is causing this problem,do this take out the drum unit remove the developer unit and rotate the develper unit gears clock wise and look for void areas on the magnet roller where develpoer adhear .
hope that help
and check your fuser rollers ?

you do need to ajust anything...just look for some sort of dirt ,in the developer unit..transfer separation unit is the unit.sets under the drum..its has 2 very thin wires.
the wires should be cleaned very gently.with pencil eraser.is good
hope that help

sound like somthing in the developer unit take out and see if developer is even across mag roller.
make sure t/s charge unit are clean
hope that help you

did you try to cleane the optic section ,make sure to remove the lens cover and clean mirror on the right side too underthe len cover,2 remove drum check and c if toner on drum?