20 Most Recent Nor-Lake Dual Access Milk Cooler, 63" W, Drop Fronts, 16 Case Capacity - Page 3 Questions & Answers

about five quarts

what is the make and model of your gate motor or central unit it might have to be reprogrammed after you dry it with a hair dryer without the battery in it

Is this electric gate on a car or truck? If not, why posted here?

About 5400 ft

You can create an account on Fixya without dealing at all with Facebook. Simply register a new account, select a user name, password, provide your email address and maybe a few more bits of information, then accept the terms of use. Installing a gate post has been done at my home, involving use of a post-hole digger for best results in digging a hole that is relatively narrow across. I'm thinking it was a foot deep, but go as deep as needed to make the top of the post as high as is needed. Pour some ready-mix cement around the post and make sure the post is properly rotated to have the gate hinge holes lined up in parallel with the gate. Hold it straight as necessary until the concrete sets.

Check out this page from Open High School. It explains the process: http://openhighschoolcourses.org/mod/book/view.php?id=258&chapterid=502 LESSON Circumference of Circles READ Find the Diameter or Radius of...

Math homework, but an English lesson involved: Proper spelling is "equation." Offhand I see possibly that we need to set up to solve 5690/6600= X/100 and cross-multiply, then solve for X Do again for 950/6600=Y/100 and cross multiply. Solve for Y. At least we get to put something together that replaces the original equation with X%+Y%=100% Now, I am leading up to Y% is the percentage change, but I need to bone-up on that point myself. Perhaps I have triggered the thought juices.

Sounds like a math homework question. I suggest you divide the given side length into the area to obtain the second side. Add the first side and second side to get the linear feet for the two sides.....

What is the issue, please be specific.

what exactly is your problem i have a gate system aswell

Linear feet is just the length of the fence in feet. Linear just means how many straight feet it is. Hope this helps. Please be sure to rate my answer. Thank you.

You need to go back to the hinges. The is a house near me that has a gated drive that rises sharply from the road. Needless to say a normal hinge system would only allow the gate an opening of a few inches. The hinges on the gate allow all the movement required, it is your problem in reverse, but the answer is the same. That is where you need to get your ironmonger to look.

There should be an external box probably by Linear that is hooked to the board, it may be inside the operator case or outside as well.

sound like a fuse blowing or a short is arcing

I would not try to do this job your self as if you manage to put it to back together and something's not right it will cause you injury. would take it to some who knows what they are doing with this model.

check the timing belt. it may have slipped a cog/ also check the spark plugs for colour and fuel on them from trying to start the engine.

no they go like is when they need a new chain. you can adjust it on the motor cog but is best to change the chain. the chain streches over time and becomes weeker

I haven't done this in a while, but I think that you have to program all remotes and the homelink at the same time. I believe that when you reprogram, the opener code changes.
Try this and if it doesn't work, don't accept my answer.
Gary

you have a welded directional contact . You need to change all directional contact tips.

is it bolted to a sleeve that was poured into the concrete? if it is, my suggestion would be to put some PB Blaster (i noticed your accent, so i will say this is an american answering. don't know if they have that in your country.) or other rust removing lubricant (WD-40, 3 n 1 oil) and lubricate it. it is probably rusted in the sleeve, and that would get the pole out. the sleeve would still be there though.