Top 20 GE 5 cu. ft. / 142 liter Chest Freezer FCM5SMWH Questions & Answers

7 is coldest.

Hi,

As the weather is getting warmer for many people their freezer and/or refrigerator do not work right because of a dirty condenser coil...

Check out this tip that I wrote about that... it is a great place to start trouble shooting your unit...and something that you can do rather then calling a repair person to do a simple thing for you...

http://www.fixya.com/support/r4024657-refrigerator_condenser_coil_cleaning


http://www.fixya.com/support/r3885294-refrigerator_troubleshooting

http://www.fixya.com/support/r4023749-refrigerator_compressor_start_capacitor

heatman101

The cold control is here. http://www.searspartsdirect.com/partsdirect/getSubComp.pd?diagramPageId=00001&componentDescription=&documentId=G0510414&modelNumber=+fcm5drbwh&productCategoryId=0141000&brandId=0432&modelName=FREEZER-B-SERIES&blt=&searchTerm=cold+control#Partslist
The defrost thermostat is about three dollars.

I got delivery today for the same freezer and had the same question.
I just called GE's customer service number (800-626-2005) and the agent told me that GE uses this button panel (which has the green on/off light switch, the two white switches, and the round control dial) for all or most of its freezers. But the buttons do not do anything on the 5 cubic foot chest freezer. They are not connected to anything and are non-active buttons. On other freezer models above this one, the two switches serve a purpose, but not the 5CF model. This is a simple, inexpensive freezer and it doesn't have bells and whistles--but it does have the same control panel as the multi-feature freezers. Hope that helps.

if the box has mold between the seal and liner the the seal isn't the main problem, the main problem is the liner is bad and by time you got both parts if you can it would cost more than to replace the freezer.
Larry

Yes, use silicon lubricant.

Great question but I cannot answer it. GE makes several models of chest freezers and they are not all wired the same. My eyesight is not to good and I cannot see your freezer so I cannot answer your question. You might try our friend google and look for the make and model of your freezer with the prefix schematic.

Was it very iced up? That can cause bad temperature registration. Also turning it off for an extended period resets the electronics. Monitor it for a week, then order the beef.

loose wire connection or motor defective

It sounds like this is a a non DIY issue. there is really not much you personally can do. Contact an authorized servicer fir best results Good luck! I’m happy to assist further over the phone at https://www.6ya.com/expert/david_dc2f9e0a44104720

The 6 or7 may be a setting number or a degree readout, which is a little on the warm side, should be around a -10 to-15. Consult your users manual for details ,.Does not sound like an emergency, but keep monitoring it' https://www.repairclinic.com/RepairHelp/Freezer-Repair-Help This site may be of help. I’m happy to assist further over the phone at https://www.6ya.com/expert/david_dc2f9e0a44104720

http://www.appliancepartspros.com/repair-help/general-electric-refrigerator-gsl25jftabs-repair/gsl25jftabs-frost-buildup.html I’m happy to assist further over the phone at https://www.6ya.com/expert/david_dc2f9e0a44104720

Gaskets can cause this, along with internal fans getting bad or iced over. Other answers might indicate a leak of freon.

the users manual does not cover this particular issue as to the temperature swing. I have seen some thermostats that are the "constant on" type that you are describing. No way of telling from the vague manual. As long as you are not storing ice cream for a long period of time, 0 degrees is usually fine for most home applications. Sorry I can not give you more info.

Make sure the electricity is connected. Check the start capacitor - check for the compressor running.

Have you tested the wall socket for power, do that first.

They are usually for extra ddehumidification based on the area you live in. If your freezer is working correctly, I would just leave them where they are at

Look on the sides or back for a louver. It's behind the louver.