Top 20 Bionaire BW2300 Window Mount Fan Questions & Answers

i bought a bionaire fan today and was looking at the manual the fuse is located at the end of the cord where it plugs into wall you have to open the square piece holding the prongs there you will see it good luck

wow... you must have got it really wet ! but if that is why it is not working now, then set it out in the sun for a few hours, or put it in front of another fan. hope this helps. post if it does. There are other problems it could be and I may be able to help with that as well. first things first. good luck. Tim

There is a major problem with the fan's electronic board. There is most likely a shorted capacitor, or some sort of fried transistor somewhere. depending on your electronics know how, try troubleshooting the circuit starting with it's power supply/input. but depending on the price of the fan, and the amount of aggrivation, I would just get a new one. Remember, most of the newer appliances today are ment to only last a few years, then die. I don't care what it is. all the companies want to do is make them as cheaply as possible, so they can sell more of them, and make more money. so don't be surprised if you can't fix it. some things are just not fixable.

The controler electronics are probably failing, or the motors are starting to pull too much current. Get in contact with Bionaire to find out who their local service is in your area for parts and repairs.

Jerry G.

Look up this fan on amazon.com. In the comments/reviews a gentleman posted instructions for fixing the thermostat (it involves opening up the fan and repositioning the thermostat wire).

I DON'T KNOW. PLEASE CONSIDER SWITCHING THE WIRES SO SAFE BAR POSITION IS 'HEAT ON' AND TILTED BAR POSITION IS 'HEAT OFF'. BE VERY CAREFUL WITH ELECTRICITY AND MORESO WHEN MAKING REPAIRS WHERE THERE MIGHT BE A CHANCE OF FUTURE FIRES. BE WELL.

These run very small motors with low "starting torque" If the fan hasn't been run for a long time, its possible that it has jammed up or got tight from just sitting there. Being careful, turn on the fan and spin it in its usual direction by hand, it should start running. If you cannot spin by hand, it may have seized up which will require you to strip and lube the motor. If you manage to get the fan spinning , let it run on high fan speed for an hour or so, it should free up and then be OK again. A small spray of WD40, CRC or similar spray can lube on the fan shaft where it disappears into the motor may assist.

go to www.americanfans.comGod bless you

www.thefind.com/.../browse-high-velocity-industrial-fan use this site

No replacement parts generally, and all are obsolete. Holmes themselves send people to eReplacement parts, and they say obsolete. Fix with Epoxy adhesive or putty, or have the part 3D printed or buy new one.

e Replacement Parts

Holmes Products https://www.holmesproducts.com > e-replacement-parts Replacement Parts. The link below will take you to a site outside of Holmes. ... Call 1-888-472-5853 for Holmes Bedding. Call 1-800-546-5637 for Holmes Appliances.

Holmes Fan Replacement Parts by Model

eReplacement Parts https://www.ereplacementparts.com > holmes-fan-parts-... Shop OEM Holmes Fan parts that fit, straight from the manufacturer. We offer model diagrams, accessories, expert repair help, and fast shipping.

Holmes Replacement Parts ' Fast Shipping at Repair Clinic

Repair Clinic https://www.repairclinic.com > Shop-For-Parts > Holme... Find Holmes Replacement Parts at RepairClinic.com. Repair for less! Fast, same day shipping. 365 day right part guaranteed return policy.

Holmes - Heating & Cooling Parts & Accessories ...

Amazon.com https://www.amazon.com > Heating-Cooling-Parts-Acce... Online shopping for Home & Kitchen from a great selection of Stove & Fireplace Accessories, Air Conditioner Parts & Accessories, Air Purifier Parts ..

1. Check the Power Supply:
   • Ensure that your dryer is receiving proper power. Use a multimeter to test the wall plug. You should have two poles giving 110-120 volts each and a ground. If only one side is hot and the other is not, you could have issues.
2. Common Causes for Dryer Not Starting:
   • Let's explore some common reasons why your dryer might not start:
     • Thermal Fuse: The thermal fuse is a safety device that protects the dryer from overheating. If it's blown, the dryer won't start. Test it for continuity using a multimeter Check your exhaust vent for restrictions..
     • Start Switch: If the dryer hums but doesn't start, the start switch might be faulty. Test it for continuity with a multimeter.
     • Door Switch: The door switch activates when the dryer door is closed. Listen for a "click" when you start the dryer. If you don't hear it, test the door switch for continuity.
3. Door Switch Solution:
   • If the door switch isn't "clicking," it might be the culprit. Try this:
     • Push the length of the switch from side to side (without removing it) to see if it clicks.
     • If it clicks, it's likely not defective.
     • Reassemble the dryer to see if it works.

Remember to safely disconnect the power before attempting any repairs. If these steps don't resolve the issue, consider seeking professional assistance or further diagnostics

Just the fan? It is here https://www.partstown.com/blue-air/blr0020-221-002 They supply parts https://www.google.com/search?q=Blueair+211%2B+replacement+fan ..

Get rid of it. The problem is likely the control board. Open this page, press CTRL+F and type 0W0912H6H and press enter. Full of issues! https://www.consumeraffairs.com/homeowners/oster_appliances.html?page=3 https://www.google.com/search?q=Oster+0W0912H6H+problems+with+display+panel ..

Do you have a phone with a front facing selfie camera? Face the front of the remote at the camera and press a button. You should see a flash. If you don't, the batteries need changing or the remote has failed. ..

2xs and 2x's is 2 extra small in clothes and not the same as '2 times'. Edited out for clarity. If the fan isn't turning, either the run capacitor has failed or the fan is binding. If the fan is turning is is part of the ionization process or there is a bad connection. What the maker says Noisy functioning (audible loud buzzing sound) is a sign that your Ionic Pro® Compact ionic air purifier is overdue for a complete clean-up of the collection blades and the internal ionizing wires. The internal ionizing wires must be kept clean to ensure silent and normal operation. May 10, 2011

Ionic Pro® Compact ionic air purifier

Or it is just worn out! https://www.google.com/search?q=ionic+pro+air+purifier+buzzing+noise ..

Sounds like you have a blockage somewhere. There may be an animal or a bird's nest in there. Dryers should be fully stripped and cleaned about every 3 years. 'Dryer Fires' are a real thing and there are companies that do nothing except clean and de-lint dryers. https://www.google.com/search?q=Dryer+Fires ..

If the light bulb in your dryer broke off in the socket and caused sparks, it's possible that the electrical system in the dryer has been damaged. Here are some steps you can take to troubleshoot the issue: 1.Start by unplugging the dryer. 2. If there are any broken pieces of the light bulb still in the socket, use needle-nose pliers or another suitable tool to remove them. Be sure to do this with caution to avoid electrical shock. 3. Inspect the area around the light bulb socket for any burnt wires, connectors, or components. If you find any damaged parts, they may need to be replaced. 4. Dryers often have thermal fuses or thermal cut-offs that can blow if there's a surge or overheating. Check the dryer's user manual to locate these components and check if they are intact. If a fuse is blown, replace it with the same type and amperage. 5. Use a multimeter to check the voltage at the dryer outlet. Ensure that you are getting the correct voltage (typically 240 volts for a dryer in the United States). If the voltage is incorrect, there may be an issue with the electrical supply or the outlet itself. 6. If you have the skills and confidence, you may open the dryer cabinet and inspect the internal wiring. Look for any burnt or damaged wires and connections. If you find any, you may need to repair or replace the affected parts. 7. If you are not comfortable or experienced with electrical repairs, it's advisable to seek the help of a professional appliance repair technician. They can thoroughly diagnose the issue and perform any necessary repairs or replacements.

If the trip blows as you switvh on the oven, it is the oven element. If your oven is a fan assisted oven, check the fan element first.