20 Most Recent Canon PowerShot SD780 IS / IXUS 100 IS Digital Camera - Page 3 Questions & Answers

Try NOT connecting your camera to your computer.

The best way to download pictures from your camera to your computer involves removing the memory card from the camera and plugging it into a card reader (either built-in to the computer or connected via USB or FireWire). This is likely to be faster than connecting the camera to the computer, and won't run down your camera's batteries.

Once the card is plugged in, it will appear to your computer as a removable drive. You can use the operating system's drag&drop facility to copy pictures from the card to the computer's hard drive, the same way you copy any other files. Or you can use Canon ZoomBrowser or any other photo cataloging program.

This is a common problem if the camera has been dropped. Canon can take care of the problem if the camera is under warrenty

This seems to be a particular issue with this model camera, noted by the archived Fixya problems listing for this model. Noting that the slide switch doesn't seem to correct this problem (resulting in 4 thumbs up) for the majority, the only other possibility is that the corresponding switch internal to the camera might be gummed up. As such, please see the "toothpick fix" (Fix #4) of this link.

SD and SDHC cards have a slide switch along one edge. The position farthest from the contacts locks the card, protecting it from writes. The position nearest the contacts unlocks the card. If the switch is already in the proper position, slide it fully the other way and then back again.

If that doesn't work, try another card.

Move the slide switch on the side of the card.

If your getting "card locked" just with that camera, then it's likely the switch in the card slot is stuck. Try the toothpick fix listed in this link to unjam it.

to thansen 3:
Yes, eventually everyone who owns this camera will see these dust orbs in every photo they take once the problem appears, and the problem continues to worsen until you will see no image at all. I've had my SD780IS for about 2 years. I was very proud of what this camera could do until the dust appeared and discovered there seems to be no do-it-yourself solution. Canon will "fix" this under warranty.
When Canon returns your camera, it will no longer take sharp photos, but the dust orbs will be gone..... for a little while. Soon, we will all tire of sending these crappy, expensive little cameras back and forth to Canon. All of us will eventually toss this expensive junk and find another expensive Canon to use for about one year before we toss that one too.
The spots appear due to the complex external lens assembly which by its very function (moving in and out) invites particulate invasion. Canon deliberately allows us no recourse for practical maintenance outside of never using the camera. Why didn't I consider this before I purchased? Well, I trusted a corporation whose mission I thought was to provide durable high quality product. The plastic disposable film cameras of yore were an honest version of what we have purchased here.
You may notice a tiny hole on the ring surrounding the lens. My guess is the Canon techs insert a $.25 tool here which with some certain push and twist of the fingers will pop the lens assembly, exposing the CCD and rear lens element for cleaning. Effective reassembly may be another matter altogether as proven by the less sharp images I experienced upon return of the SD780IS from Canon. I have yet to locate any good solution addressing this difficulty. However, my wife still likes this camera despite her 20/950 vision. Some people are very easy to please. When she notices the spots, I'll look into getting her another camera.

Download the player below.

http://www.videolan.org/vlc/

If the player is able to play the videos then the problem might be with the codec or u might not be having the codec or the codec has broken.

Hello and Welcome to FixYa!
Yes, it has been seed that other similar model cables doesn't work properly due to minor changes in their structure, although he connectors are same but I'll recommend you to get the original cable for your cam.
The inappropriate cable may end up in some other loss.
I hope you understand.
If you have any Confusion, questions or issues regarding your problem do tell me.
Thank you for using FixYa!, Keep visiting..

If you think I was of help, your token of appreciation in the form of rating and a testimonial will be esteemed.
Concerned, Nooh: FixYa Team.

Hello

Thank you for using FIXYA!!!

This is a suggestion. If you do not feel comfortable trying it, you will need to take the unit to your nearest service centre. Feel free to let me know if you need any assistance.

The problem might be that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the probability is that you will have to get it fixed by a professional.

Use these at own risk as it may further damage the camera.

Firstly , try connecting your ac adapter or usb cable.

Try holding the shutter button while switching on the camera.

Look at the lens , and if some of the lens 'circles' is misaligned or not concentric then try wiggling it (while holding camera lens down).

Try gently pushing or pulling the lens when it extends but this is risky as it may cause the lens barrel to slip out of its guidance system.

Another way to do this is to place the camera lens down on a hard surface and then power it up. Be sure to use a soft cloth or something similar as to not scratch your lens or casing. Let the lens push the camera up and down a few times and sometimes the little resistance provided by the camera is enough to get things going again.

Try hitting your camera near the lens on the body with the soft tissue on the palm of your hand.

Other than that , I would take the camera to a repair centre for a evaluation to see if it would cost more to repair than to replace the camera.

If it is still under warranty I would suggest you take it in before trying any of these steps and remove any off-brand batteries or accessories as some stores are really fussy about warranty repairs on camera's with non-brand accessories.

You can also have a look at THIS link.

Hope the advise is useful. please do not hesitate to let me know if you need any further assistance. Also, please be so kind to let me know if you found this helpful.

Regards
Andrea

Try NOT connecting your camera to your computer.

The best way to download pictures from your camera to your computer involves removing the memory card from the camera and plugging it into a card reader (either built-in to the computer or connected via USB or FireWire). This is likely to be faster than connecting the camera to the computer, and won't run down your camera's batteries.

Once the card is plugged in, it will appear to your computer as a removable drive. You can use the operating system's drag&drop facility to copy pictures from the card to the computer's hard drive, the same way you copy any other files. Or you can use iPhoto or any other photo cataloging program.

Hello

Thank you for using FIXYA!!!

This is a suggestion. If you do not feel comfortable trying it, you will need to take the unit to your nearest service centre. Feel free to let me know if you need any assistance.

The problem might be that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the probability is that you will have to get it fixed by a professional.

Use these at own risk as it may further damage the camera.

Firstly , try connecting your ac adapter or usb cable.

Try holding the shutter button while switching on the camera.

Look at the lens , and if some of the lens 'circles' is misaligned or not concentric then try wiggling it (while holding camera lens down).

Try gently pushing or pulling the lens when it extends but this is risky as it may cause the lens barrel to slip out of its guidance system.

Another way to do this is to place the camera lens down on a hard surface and then power it up. Be sure to use a soft cloth or something similar as to not scratch your lens or casing. Let the lens push the camera up and down a few times and sometimes the little resistance provided by the camera is enough to get things going again.

Try hitting your camera near the lens on the body with the soft tissue on the palm of your hand.

Other than that , I would take the camera to a repair centre for a evaluation to see if it would cost more to repair than to replace the camera.

If it is still under warranty I would suggest you take it in before trying any of these steps and remove any off-brand batteries or accessories as some stores are really fussy about warranty repairs on camera's with non-brand accessories.

You can also have a look at THIS link.

Hope the advise is useful. please do not hesitate to let me know if you need any further assistance. Also, please be so kind to let me know if you found this helpful.

Regards
Andrea

Fixing a Lens Error on a Digital Camera

This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include "E18 lens error", or "lens error, restart camera". Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.

The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous interiors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many cameras, and NEVER use a case for this very reason.

A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.

Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.

The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:

Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.

Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.

Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particles that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.

Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.

Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in "no heat" setting, or sucking the gaps with a vacuum (careful with this one).

Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.

Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.

Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.

Consider NOT connecting your camera to your computer.

The best way to download pictures from your camera to your computer involves removing the memory card from the camera and plugging it into a card reader (either built-in to the computer or connected via USB or FireWire). This is likely to be faster than connecting the camera to the computer, and won't run down your camera's batteries.

Once the card is plugged in, it will appear to your computer as a removable drive. You can use the operating system's drag&drop facility to copy pictures from the card to the computer's hard drive, the same way you copy any other files. Or you can use iPhoto or any other photo cataloging program.

Try NOT connecting your camera to your computer.

The best way to download pictures from your camera to your computer involves removing the memory card from the camera and plugging it into a card reader (either built-in to the computer or connected via USB or FireWire). This is likely to be faster than connecting the camera to the computer, and won't run down your camera's batteries.

Once the card is plugged in, it will appear to your computer as a removable drive. You can use the operating system's drag&drop facility to copy pictures from the card to the computer's hard drive, the same way you copy any other files. Or you can use any photo cataloging program.

Try NOT connecting your camera to your computer.

The best way to download pictures from your camera to your computer involves removing the memory card from the camera and plugging it into a card reader (either built-in to the computer or connected via USB or FireWire). This is likely to be faster than connecting the camera to the computer, and won't run down your camera's batteries.

Once the card is plugged in, it will appear to your computer as a removable drive. You can use the operating system's drag&drop facility to copy pictures from the card to the computer's hard drive, the same way you copy any other files. Or you can use iPhoto or any other photo cataloging program.

Try NOT connecting your camera to your computer.

The best way to download pictures from your camera to your computer involves removing the memory card from the camera and plugging it into a card reader (either built-in to the computer or connected via USB or FireWire). This is likely to be faster than connecting the camera to the computer, and won't run down your camera's batteries.

Once the card is plugged in, it will appear to your computer as a removable drive. You can use the operating system's drag&drop facility to copy pictures from the card to the computer's hard drive, the same way you copy any other files. Or you can use any photo cataloging program.

This is the first time that this occurs? Is the battery new, how time is working with this battery? Are you try with another battery?

Also, keep in mind turn off the LCD screen to save power. If nothing comes on at all, then try looking for a reset button. It's usually a very small button you have to press with a paperclip or something like that. Look near the bottom of the camera, or under a cover, if there are any on the camera. I would take the memory card out of the camera before you press the reset button, just to be sure it doesn't delete the pictures.

If the camera still does not power on, contact Canon support for servicing and repair.
Hope helps.

You can try burying it in a bowl of uncooked rice for a week. However, if you tried to start it up while water was inside the circuits, you may have fried them.