Top 20 GE 36 in. Monogram ZEU769 Electric Cooktop Questions & Answers

Cooktop Cleaner If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Hi, I assume we are talking about a flat glass top. First the bad news. using any abrasives will permanently scratch the glass hence the dull spot. You can however make it look a little better. Grease spots and the like can be removed with a flat razor blade scraper which needs to be held flat to avoid the corners making scratches. Use any good glass/ceramic cooktop cleaner ( which is the ONLY cleaner you should ever use ) (available in your local grocery diy store and some hardware stores). The cleaner is a thick liquid, put about a dime size drop on each burner area and use a paper towel to buff out the finish like waxing a car. Once it looks clean flip your paper towel over and shine the top to like new. Good Luck!

Hi,
Here is a tip that I wrote that will help figure out why the burner spark keepson clicking...

Gas Range RepairBurners Keep on Clicking
heatman101
fsggfs

You can't modify gas appliances.

I have an early 1970s GE, and we keep saying when it breaks down, we will replace it, but apart from replacing elements, it just goes on and on. Unfortunately, neither of your numbers give results. There should be a plate near the power lead that has the details and some have a parts manual and wiring diagram in the rear of the console if it has one. https://www.google.com/search?q=GE+82212+cooktop https://www.google.com/search?q=GE+YT123887L+cooktop ..

Question edited for clarity. There is no fuse, the loads are too great. The Service Manual is in the link. Check the Control Lock on Page 11. https://ja.safe-manuals.com/source/pdf/adea1af72b5b020af66562d603ff2631 https://www.google.com/search?q=ge+pp975s+fuse+location ....

It is a gas appliance. From the installation manual. Installation and service must be performed by a qualified installer, service agency or the gas supplier. It needs to come out as there is almost certainly fixings from below. Screws on the burners, only hold the burner rings down. The installation manual doesn't say how the top comes off, just how to install. No Service Manual for it. https://www.manualslib.com/manual/57348/Ge-Jgp630.html?page=1#manual ..

Take out the right front burner and use your multimeter to check it for continuity. Only then can you be sure that the error code isn't lying to you. It is my guess, that with an error message so specific, that if no burners are working, it is not the front right burner at all. Hands on testing is the only way to be sure. F152 means the right front burner has failed, the sensor in it is bad, the burner will need to be replaced.

error code F152 ' Appliance Video

The element is $225.00 so it is not something to change on a guess. Full testing procedure here, or call for a Service Engineer. https://www.appliancepartspros.com/answers-for-ge-element-radiant-lt-wb30t10080-ap3188020-question-148609.html ..

do an online search or if a repair shop in area order from them

TRY SOME LUBRICATION ONCE THEY DO GUM UP YOU KNOW

most likely the keypad is defective.

The induction cooktop will flash "F" when cookware has been removed from the surface; cookware is not present when the unit is turned on; or cookware is not centered on the element. Position the cookware properly over the center of the cooking surface if the error code "F" flashes. Use only induction cookware and use a bigger pan, as the error code "F" indicates that the pan is too small for the cooking element.

There are several helpful how-to videos on Youtube but please be aware induction hobs work on a principle different from the usual and the troubleshooting and repair is considered a specialist task - if you wouldn't poke around inside a tv or a computer then you probably shouldn't poke around inside your hob.

Yes, turn it off and get a gas tech out to check it.

go to this link and you should find the manual...or the diagram.. Wiring diagram ge jp350 Google Search

I think you need to replace the key pad control panel.

This is not to code. The white is neutral and is of the same polarity as a bare wire. The red and the black are considered hot and would be 220.

Try pushing it in and turn, if no sucess replace switch turn off gas first.