Patton Electric Utility Heater, PUH680-WM1 - Answered Questions & Fixed issues

Parts Suppliers https://www.google.com/search?q=Patton+PUH680+parts ..

If the light on your Patton space heater is on, but the heater will not start, there are a few things you can try to fix the issue:

1. Check the power source: Make sure the heater is plugged into a working outlet and that the circuit breaker or fuse is not tripped.
2. Check the thermostat: Make sure the thermostat is set to a temperature higher than the current room temperature. If the thermostat is set too low, the heater will not turn on.
3. Check the safety features: Some space heaters have safety features, such as a tip-over switch or overheating protection, that will shut off the heater if it is not positioned properly or if it gets too hot. Check to make sure the heater is positioned correctly and not too close to anything that could cause it to overheat.
4. Clean the heater: Over time, dust and debris can accumulate in the heater, which can cause it to malfunction. Unplug the heater and clean it thoroughly, making sure to remove any debris from the heating element.

If none of these steps resolve the issue, there may be a problem with the heater's internal components. In that case, it is best to contact the manufacturer or a qualified repair technician for further assistance.

Unfortunately you can't. These are made overseas and badged to whomever sells them. The manual for the 9000 model is available, but not yours. This may be the closest? http://www.useandcaremanuals.com/pdf/WOFH7167.pdf https://www.google.com/search?q=Patton+POH2420+manual ..

I would try the manufacturers web site.

Check the base for a tip over safety switch. It needs to be pressed in. Can't find a manual for it as it appears to be an Amazon, Walmart special. Try it in another outlet, or put something else in that outlet that is known to work like your cellphone charger. https://www.walmart.com/ip/Patton-Radiant-Heater/15126054 https://www.google.com/search?q=Patton+PRH11+manual .. ..

Wires are rated to handle a certain amount of amps. Your dryer cord is bigger than your coffee maker cord because your dryer pulls more amps. What is going on with your heater is your heater is drawing more amps than the wire can handle. Therefore the wire is getting hot, melting the insulation. Hopefully it shorts out before it catches on fire!!! BOTH BAD SCENERIOS!!! It is possible your machine is just excessively dirty, therefore working extremely hard, drawing high amps. If you are able to give a good cleaning, do so. Let dry and turn heater on DURING A TIME WHEN YOU CAN MONITOR IT, NOT OVERNIGHT. See if it has made a significant improvement. If not, it's time for a new heater!! Best Wishes!! If you need further help, reach me via phone at https://www.6ya.com/expert/thomas_092728000e6acb79

Work 1 foward

I doubt that they have any Teflon in them, and it would certainly have burned off by now if it did.

You need to include more information: Model number would be helpful. You could also try checking your product manual and seeing if they list a way to unlock the phone.

The thermostat is probably shot. These units are repairable but disposable, meaning the repair will likely cost as much as a new unit.

Please see the two previous answers to your question.

Look you need to contact Patton Heaters directly and let them know about their faulty product. While you are at it give that son of yours a big hug and kiss and let him know how much you really love him. This site is people like myself giving helpful hints on repairing products we are not a part of Patton or are we affiliated with them. Consumers affairs may be worth your while as well, try Better Business too. You are very fortunate to have this out come.

More than likely, the alarm is a warning that the heater is not sitting perfectly level, check to make sure that it is sitting level. Or it could be a carbon monoxide warning. Open a window, just slightly, and see if that fixes the problem. Also, the appliance could be overheating, which could be a problem.

HEY< that could be the trouble, before you buy a circuit board cause it sounds like its doing its job. Take the rubber hose aloose from the fan switch and and while its starting, put the hose in your mouth to feel a suctions if not or a soft suction , then remove the hose off the motor while off and clear the end out with something that ,ll clean the opening out and connect the hose back and start the system again. T Y V M!

Return heater to Home Depot.

THAT COULD BE THE PROBLEM, BUT CHECK YOUR UNIT AND SEE IF THERE IS A RECALL FOR YOUR UNIT. 2 UNITS THAT I KNOW OF ARE PATTON M# HF-10 AND SEARS M# 201-7208

x48987

Question edited for clarity, full 'make model (what it is)'. Email address removed. You don't need the site's 12 million annual viewers emailing you to say they can fix it for a thousand bucks! Finally, Please don't type in all CAPS, it is considered SHOUTING and is harder to read. Repair Clinic has some good ideas, but your model is discontinued

Fedders Air conditioner won't turn off

Repair Clinic https://www.repairclinic.com > RepairHelp > Fedders-Ai... Here are the most common reasons your Fedders AC compressor won't turn off - and the parts & instructions to fix the problem yourself.

Why Your Air Conditioner Isn't Shutting Off, and How to Fix It

Williams Comfort Air https://williamscomfortair.com > ac-wont-shut-off When your air conditioner won't shut off, it's natural to worry about wasting electrical power as temperatures become too cool for comfort. ..

Here are the steps you might want to follow: Setting the Draining Cycle Times (Dump Interval): This setting controls how often the unit dumps the water. You can adjust this setting to reduce the frequency of water dumping. Setting the Drain off Delay Time (Dump Delay): This setting controls the delay time before the unit starts to dump the water after it has been turned off. If adjusting these settings doesn't work, there could be other issues with your unit. For example, a continuous water dumping problem could be due to a faulty dump valve or a problem with the float valve.

Frego split ac error code h3 what is problem