Top 20
Lanier 1205 Copier - Page 7 Questions & Answers
We have a lanier 5216
Hi,
System Setting Reset
The system settings in the UP mode can be reset to theirdefaults. Use the following procedure.
1. Press User Tools/Counter .
2. Hold down the '#' key and then press System Settings.
3. Press yes when the message prompts you to confirm thatyou want to reset the system settings.
4.Press exit when the message tells you that the settings have been reset.Please do rate the solution if the issue is resolved or post a comment for further assistance.
Thank you for using fixya have a nice day:-)
Double sided copying does not
look my friend try to open side door and move that two rullers hanging in exit unit try to move more than 5 on's it's works
Lanier 6613 copier. Image is offset down the page
try making a copy and then open the door when the paper is in the center of the machine. if the image is offset before the paper hits the fuser(hot) rollers>the problem is in your drum unit (most likely a cleaning blade. If it happens after going through the fuser(hot) rollers you have a fuser roller problem. Most likely you have a worn drum cleaning blade which is cheaper the a drum. Good Luck.
I have a lanier 7328/7320.
How are you? This is a problem with front door switch.
Remedy
- Place the machine on a level table and make sure all the four stands are landing freely on this table.
- Check that the front door notch that closes the door switch is not broken and if it is replace that particular door or modify the notch.
- Make sure the upper half of copier is well locked with the lower bottom part.
If all the above is correct, and still reads open, replace the door switch.
Good luck.
Sc 495
SC495 is generally a problem with the toner recycling system in a Lanier copier. Without knowing the specific model, I can't give you any more information. What model copier do you have?
Will only copy documents landscape no matter how
if you are yousing the ARDF keep the document in ARDF ensure that the mater on the document is up side or you are yousing the platen glass keep the document down side on the glass thatsit - thankyou
We just got a Lanier
We also just had someone donate this same type of copier to us and do have a manual. We are currently having trouble with the stapling unit running continuously. The manual is about 130 pages. I may be able to scan it to you in a few days if you'd like.
How to enter service mode on a lanier ld225
Press Clear/Modes, then 107, then press AND HOLD Clear/Stop
This will get you into the service mode screen.
Know what you are doing before going into any modes and changing anything.
Good Luck and Thank You for using Fixya
Copying a 40 page documente
Well sometimes you can restart the printer...also you can start printing where it left off if you see what page it was and then hit print and look in window and set start page such as 21-40
I have a lanier
Remove your printer from the PC and uninstall the printer software. make sure there is no other conflicting softwares in the pc specially recently downloaded programs. If so uninstall them too. Now reinstall the printer software and connect the Printer to be detected and installed. Check printer properties to see the ink levels.
Now make a test to see if the PC commands the printer. If there is no response, check the head assembly/ ink carriage to be struck or out of alignment. Check for possible realignment of any of these mechanical problems., jammed roller or head drive
If the catridges were removed make sure they are in place . If you are removing them make sure that the printer is shut off .
If none work it can also be an error inthe main board. Need to swap one to confirm
How do you enlarge copies
The option for enlarging copies on any printer are usually found under the "properties", or, "preference" tab/button. There should be sub-tab that says "scaling" that is defaulted at 100 percent. Increasing that number enlarges the copy.
Hope this helps. :)
Lanier ld 435 color print code sc548
re install fixing unit and do the sc reset. press clear mode 2x 107 press clear/stop until COPY SP appears press Copy Sp then exit, turn off machine then on after 5 to 10 seconds
Not finding what you are looking for?