20 Most Recent Lanier 1205 Copier - Page 3 Questions & Answers


Your problem in the exposure lamp unit.Check the expo lamp,expo thermofuse continuity,and perform the Auto Image Density Sensor control proces after the clean the mirrors and the glass.

Lanier 1205... | Answered on Oct 08, 2009


Hello sir; Please contact with me by email, I can get it for you.

Lanier 1205... | Answered on Jul 18, 2009


Try a software reset which involes holding down the * and # (next to the 0) buttons for about 10 seconds until you hear a beap. You should then see "Now loading. Plese wait" and it should start up normally.

Its possible the machine has just locked up. If the above procudure dosen't work power off at the power piont and leave off overnight.

Please advise if any SC codes are present with the spanner for further help.

Lanier 1205... | Answered on Jul 06, 2009


Cleaned the coronas as per instruction book. Done this before but this time it made a difference.

Lanier 1205... | Answered on Jul 02, 2009


If you are talking about the sensor in the paper tray tape the sensor so it is "actuated" and tuck it in the slot near by, the only problem you will have is the copier wont know when you are out of paper. The switch mounts break.

Lanier 1205... | Answered on Jun 18, 2009


Hello sir; The paper stuck in your paper tray ,I believe in first tray, pull out tray you will find out.

Lanier 1205... | Answered on May 02, 2009


I believe c-41 is a fuser problem. A trained copier tech may be required to troubleshoot.

Lanier 1205... | Answered on Apr 29, 2009


IF THE PAPER IS LAYING FLAT ON THE TRANSPORT WHEN THE JAM OCCURS, THE PROBLEM MAY BE A DIRTY TRANSPORT BELT SENSOR. A TECHNICIAN IS REQUIRED TO REPAIR THIS, AS IT INVOLVES DISASSEMBLY OF THE IMAGING UNIT.

Lanier 1205... | Answered on Jan 01, 2009


Presure roller warm-up error.

Lanier 1205... | Answered on Dec 11, 2008


SC101 can be caused by a dirty WHITE LEADING EDGE STRIP. This is located under the left side plastic strip that holds down the exposure glass on the left side. Remove the screws, and flip over the glass holder. Clean the white strip with glass cleaner, and reassemble. If SC101 reappears, the scanner drive pulley screws are loose or broken off. A service technician is required for this repair.

Lanier 1205... | Answered on Aug 08, 2008


Sounds like a dirty sensor or a small piece of paper stuck. Check the feeder, left side, underneath. There should be a switch actuator
in the paper path that is visible. Also, on the right side, check all of the openings for anything stuck. If you have no luck, get some canned air and blow out everything. If its still jammed, it can be easily unplugged in the back of the machine, and the machine section will still operate.

Lanier 1205... | Answered on Apr 23, 2008


No, you will have to put your paper like you want( one sheet white and one sheet yellow and so on ) and put it in the same tray !

Lanier 1205... | Answered on Mar 26, 2008


hi im jules_09,have you tried cleaning all the ruber roller?try cleaning all ruber roller then lubricate al bushing and gears.if there is still a problem check all paper sensor it can be cleaned with alcohol.just soak the paper sensor with alcohol then let dry after a few minute then install it back again in the copier.dont soak the paper sensor in alcohol while it is in the machine.turn of the copier first

Lanier 1205... | Answered on Nov 09, 2007

Not finding what you are looking for?
Office Equipment & Supplies Logo

Popular Tags

66 questions posted

Ask a Question

Usually answered in minutes!

Top Lanier Office Equipment & Supplies Experts

quennie732

Level 2 Expert

422 Answers

Adorjani Laszlo

Level 3 Expert

1316 Answers

gggg

Level 3 Expert

904 Answers

Are you a Lanier Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Lanier Office Equipment & Supplies

  • Lanier Office Equipment & Supplies

Most Popular Question

paper coming out

  • Office Equipment & Supplies
Loading...