20 Most Recent Lanier 1205 Copier - Page 2 Questions & Answers

i'm very confused what is your model please

Zebra striping is typically caused by a bad development clutch. Most likely, the developer and the development clutch will need to be replaced, but the 7313 is so old you may have trouble finding parts, or finding a technician to work on the machine.

Hi, you can turn off the key code management by going into User Tools. Press the User Tools/Counter button, then go to System Settings and then Admin Tools. There should be an option on the screen (you may have to scroll down) for key counter management -- turn this option off.
When you exit out of User Tools, you should be able to see the Copy screen just like you normally would, without having to enter a key code.
If the message on screen is asking you for a User Code rather than a key code or key counter, that option can also be disabled in User Tools. Go back into the Admin Tools and look for an option called User Authentication Management, or something similar, and either disable it completely or disable it for copying.

This is a hot section problem, can be reset by entering service mode (pushing in sequence clear modes 1-0-7 hold stop button down for 5 seconds) but this is a bad code...service call? -Carl

The developer is not a toner. It goes in the developer unit, it is installed by a service rep. You need to empty out the used developer & install the new bag of developer & rest the counter & set the developer up to add toner when needed. To make a long story on developer short > it is made up of iron filings & it holds the toner on the developer make roller to make a even coat of toner on your paper... Good Luck..... Just to let you know your copier is a Ricoh and it is a dul component copier

exposure lamp open circuit replace or lamp regulator faulty also check thermo fuse 1st thing to check change auto exposure to manual this will tell you if regulator is faulty or not

Hello.

This is probably because there is something that doesn't belong inside the printers paper path.

1. Turn off the printer / copier.
2. Remove any paper trays. Inspect them for wrinkled or damaged paper.
3. Also open the back cover of the printer if this model has one.
4. Open any other doors that give access to the printer's paper path and to the toner or ink cartridge.
5. If necessary, remove the toner or ink cartridge. Place it away from light/ sun light to avoid damaging it.
6. If you find a piece of jammed paper, remove it by holding it with both hands and pulling firmly. The goal is to keep the paper from tearing. If several pieces are jammed together, try pulling out the middle piece first to loosen the jam.
7. If the paper does tear, try rotating the roller gears manually to free the paper. Don't force anything, though. Do this step especially if the jam message comes up repeatedly without any obvious paper jam, there may be a small tear of paper inside.
8. Ones the printer is free of paper Replace the toner or ink cartridge and paper trays, close any doors you opened and turn the printer back on.
9. If the printer paper jam message still appears, then there is still some paper in the printer. Reinspect the paper path.
10. see alternative if the problem is still not solved.
    

alternative :
Load a piece of thick paper, for example photo paper and press the resume button (may be diffrent button on diffrent models) a few times to the printer picks up the paper and puts it through the machine.



Advanced

If that doesn't help then you would have to start taking apart the machine to find the object or source of trouble inside. A service manual would be recommended as the paper path has alot of small moving parts and taking apart the whole printer will be very complex, it will turn into alot of small parts.


It may be best to get a professional to inspect the machine, if you can't find whats causing it by opening all the covers and looking closely with a flash light or similar. I would not recommend taking apart the printer yourself too much as if not put back together the right way it might make the problem worse.

2 ways to check the meter.

press the user tools button on the op panel. on the screen press counter. you can either view the counter on the screen, or press print counter, and it will give you a hard copy.

the 2nd way is to look behind the front cover, probably behind a piece of tape, on the right side, about half way down.

What is the error code? Many of the codes refer to a general electrical problem, and often turning the machine off, resetting the circuit board connectors and harnesses and memory sticks, and turning the machine back on will clear the error code and allow the machine to boot up normally.

What kind of copier is it? On many of the Lanier color copiers, the waste toner bottle is located on the lower left side inside the front door.

Turn the copier off first. Pull the big front door open and turn the bottle with the oil to the left -- the waste toner bottle is the plastic gray tank behind that. Slide it out (carefully) and dump it in a plastic trash bag, then reinsert it.

If you have a different kind of copier, please specify the model and I'll tell you how to get to the waste toner bottle.

This is a fuser error code resetable by entering service mode. -Carl

sc541 means no warm up, press the clear modees the punch in107 then press and hold down the clear stop key untilk it goes into sevice mode then shut main power

Check the point where the door meets the switch on the front of the machine make sure nothing is blocking the switch and that the switch get pushed in while the cover is closing

It was very easy. I just had not seen the machine when I posted the question. Thanks

Hello sir; It seems like drum blade worm out need to replace also possible fuser roller worm out too ,my suggestion is replace both of them.

That is a CALL SERVICEMAN code, something is broken that only a service tech can diagnose.

sure you lamp lights up when machine is powered on. open the top cover, turn power on. lamp should light and scanner should move. if either of these do not happen you will need to replace parts. if the lamp lights and the scanner moves your ccd could be bad. you may need a service tech. if the lamp does not light it is your problem. lamp, power supply, ballest, or main pcb could be the problem

The clutches arnt too bad putting them in however... I own this model as a home copier but parts are hard to come by and to get a tech that knows how to repair is harder.