Dell PowerEdge T300 Server - Page 2 - Answered Questions & Fixed issues

NIC teaming is useless unless you have a switch that support teaming.
However, Dell servers have free lifetime phone support ((800) 945-3355).
They should be able to help.

go here

http://support.dell.com/support/edocs/systems/pet300/en/hom/html/about.htm

driver here hp v165w driver

Computer not recognizing the hard drive. Look in BIOS to see if hard drive is listed. Reload system disc/CD.

It could be a couple of things 1. the computer Cpu fan is not working or is clogged inspect it and clean or replace.2 The power supply could be bad

Namrata_stha, The I912 error is referring to the System Event Log is full of events and because of this is unable to log anymore. You must clear the log in order for the Server Management controller to log any more events. Now depending on the OS installed there are different ways to clear it. If Windows Server 2k8 you would use this command - wevtutil el ' foreach { wevtutil cl $_ } Where with Server 2003 you can go tot he Event viewer and clear it. Let me know if this helps.

www.hp.com/support

Please be more specific. You haven't actually asked a question. What are you trying to do? What happens that you aren't expecting?

You will have to get into the controlled setup in order to find out what the problem is, or you can simply hit ctrl-D and do the Dell disk diagnostics which will take an hour or more, but will give you an idea of where to start. Logically, if it won't boot, then your RAID is probably broken. it can sometimes be repaired through either the RAID or controller setup menu, which you can see during boot. go here, for the manuals and documentation on how to do that: http://www.dell.com/support/home/us/en/19/product-support/product/poweredge-t105/manuals

what is your server model? in most cases you can use the operating disc to format the server drives

Go to start menu. click on 'control panel'. Select 'system and security". Then select 'system'. This should give you the info.

You can download the service manual from Dell`s website or either check some youtube tutorials if available.

Is it in a 1, 3, 2 beep pattern (beep....beep, beep, beep........beep, beep)? If so, the memory is either not seated well or may be bad. Try reseating your memory. If it continues, try with one stick at a time just to see if it will boot up with a display.Thanks,--Brian

Please replace CMOS battery and then will not be losing time.Regards,Kaushik Patel

Kindly start windows in safe mode by pressing F8 key while powering up, Goto device manager and uninstall any new installed drivers or device. Regards,Kaushik Patel

What question do you have about your battery? Do you need to order one or are you experiencing low battery life?

Best is to find a support or systems engineer on http://www.qual.ch if you are in Switzerland and for the UK you can find find a top Dell expert or systems specialist on http://qualifind.co.uk -- I just asked one (from Qualifind) and was informed you just need to install Openmanage and clear the logs from there, no need to down the server.

Step 1:

First open look on the back off your pc and see if you have an onboard video card (closer to the power supply and pointed up and down or one much lower down towards the last two-thirds off the case....

Step 2:

If you have an onboard I would think it's toast but if you have a seperate video card swap it out for another one and if that don't work I would guess it's your motherboard.....

I don't know of any server that supports Crossfire or SLI. I would say no.

Hello here is the homepage:http://www.dell.com/support/drivers/us/en/04/Product/poweredge-r710Yes, that will be okay.But a SSD harddrive is much faster, than the old mecanical one.I know they are a little more expensive, but you will see a speed improvement, you have newer seen before.Good luck